Subject: Mazdatrix one rotor LSA engine. RX8 ignition coils 2 ms dwell
From: Rotary Engine
Date: 11/22/2011, 6:14 AM
To: AAA Put this in the To box




    One item you mentioned below needs some clarification.
    The RX8 coil can not be used in a simple ignition as implied, because
 of
    the
    2ms dwell time required. The trigger is at the rising edge of a 2ms
  square
    wave, and coil firing is at the falling edge. This will give you a
  90deg.
    retarded ignition at 7500RPM.
    I believe we talked about that already a few years back.

    It would be nice, if someone came up with a simple electronic setup,
    without
    a microprocessor, taking care of that.

    Richard Sohn
    N2071U


 http://www.fairpoint.net/~res12/home.html

    Real easy to do that Richard with a 555. It is called
    a non-retriggerable one shot.

    Paul Lamar

    I missed your point at first. Yes I can see how that
    could be a real problem at high RPM.

    Paul Lamar


  Paul and Richard,
  If you use a Hall Effect sensor for your trigger you can use it to
 advance
  the timing too. Kawasaki used this system with some of their old CDI
  systems. They would space the sensor as far from the magnet as would
  reliably trigger. Then as engine rpm rose the leading edge of the sine
  wave
  would trigger the thyristor trip voltage sooner naturally. This would
  cause
  the system to fire sooner and advance the timing. The max advance was
  about
  12-15 degrees but it was enough to make a difference with not one moving
  part. It worked perfectly, and there was no way for it to go wrong if the
  sensor was still functional.
  Bill Jepson

  I was talking to Randy this after noon about the dwell phenomena and I
  realized
  that I had forgotten that a capacitor discharge ignition does not do
 that.

  If you are using a carb and you need a stand alone ignition just buy
  an MSD capacitor discharge system. CD systems use the same old simple
  coil differently. They do not use the rapid break down of the magnet
  field in the coil to form the spark. They use the coil as a pulse
  transformer.
  When the capacitor charge is dumped into the primary winding of the coil
  it fires the plugs with no delay. Within microseconds. No need for a
 dwell
  time
  to build up the current in the coil.

  Of course this gives you no advance but it solves the retard problem
  mentioned by Richard due to the required dwell time being a significant
  amount of time relative to the time it takes the engine to make one
  revolution at 7500 RPM.

  You may want to add a mechanical advance for high altitude lean burn
  as per the jpg.

  Paul Lamar


  Paul:

  Check out the DYNATECH ARC-2 at
  http://www.dynaonline.com/skins/products/sportbikes/arc_2/. Looks like it
  has 2 triggered inputs to CDI ignition that could easily use the
  hall-effect
  trigger (or other OEM trigger).

  Richard

  Looks good. You need two for the trailing plugs on a two rotor
  and one for the leading plugs. Very pricey at $400 each.

  One can buy an MSD6 on ebay for as little as $50 each.


  The cheapest way to implement CDI is use the outboard motor
  way and put the magnets on the flywheel. Perfect for a one rotor.
  Very reliable. Better than a magneto.

  Here are the illustrations. Bill Jepson's advance suggestion
  is here as well.


  Paul Lamar


 To make one thing clear, I do not have any problem with the CDI ignition,
 except for the cranking problem. This cranking thing does not show up on
 the
 test stand, because the engine is already worn in(or out) compared to the
 new one. My engine runs 6200RPM static WOT. EGT peak is 1700F and engine
 sputter starts at about 1500 LOP.

 The improvements I am looking for are more of what I like than what I
 need.

 Richard Sohn
 N2071U
 www.fairpoint.net/~res12/home.html


 MSD sells a box that retards the ignition to help starting.
 One might even be able to hand prop it.


 Paul Lamar

From what I understand, the MSD does not fire unless the 2nd trigger
occurs no more then 200ms after the first one. What I found was it is
firing at 350RPM but not at 250RPM. I was told that there is a similar
feature in Tracy's ECU for preventing it to fire if it is triggered just
one time.

If that is correct, a timing retard would not make a difference.

Richard Sohn
N2071U
www.fairpoint.net/~res12/home.html


Have you contacted MSD on this Richard?
http://www.msdignition.com/troubleshooting.aspx

Paul Lamar


FYI. I ran MSD 6 ignition on a roller cam 302 with '68 four barrel heads I
built for my '76 Ford truck.  Had two of them fail after year or so.
They are not indestructible as I had thought.  If one has a backup, no prob.

Van

What year was that? I am sure they have come a long way in the past few years.
Since we need two per rotor a failure of one won't be catastrophic.


Lamar
-- 
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Youtube key word PaulLamar2
Copyright 1998-2011 All world wide rights reserved.