Subject: Eccentric shaft end play
From: Rotary Engine
Date: 12/21/2011, 10:40 AM
To: AAA Put this in the To box



I am  performing an engine overhaul. The shaft turns smoothly and
has end   play without binding before performing the eccentric end
play check.  The end    play is 0 and I have gone to a maximum  spacer
thickness of 8.12 mm spacer    stamp s which gives a  slight end play
clearance until tightening the bolt.    It still  turns smoothly with
a nice compression popping sound. The bearings   are properly
mounted on the spacer and 2 thrust plates are installed  per    procedures.

Any ideas on this ?

John P

I  assume you have the shop manual.

One can download them from here  free.

http://foxed.ca/index.php?page=rx7manual


Paul  Lamar


Paul

I have the shop manual and other Info. I   overhauled  other rotary
engines but may  have ignored previous  eccentric shaft end play.

John P

Final assembly must be done  vertically as the needle bearing can
fall out of place. That is about the  only thing that can go wrong.
Most manuals do not cover that well. In fact  it shows it
done horizontally. The 76 Cosmo manual is very clear on  this.
Step 1 is turning the engine on the engine stand so the front  of
the engine is up.

What year is this engine?

Maybe I am  missing the point here.
If so the attached pictures and above text are for  the new guys.

Perhaps you need to machine a longer spacer.
I have a  guy that can do that and he only charges $35 and hour.
If so send me a  spacer he can measure and  make a new one.

Paul  Lamar


Paul

I would like to take you up on your offer for a  thicker spacer.
The only difference in the above listed spacers is that I  would try
a 8.14mm thickness spacer. The engine is a 1991 2nd generation.  The
eccentric end shaft is straight 30mm dia. The spacer inside  diameter
must be slightly larger for clearance. The spacer od is 35mm-.  The
needle bearing race id is 35mm and rides over the spacer. Any of  the
above spacers could be measured and checked against clearance to  the
30mm eccentric shaft and 35mm id needle bearing races.  The
additional required 8.14mm thickness is then required. I will send  a
K stamp 8.06mm thickness which fits another engine and gives the
same  required inner and outer clearances. The bearing race is
included to check  spacer clearance. If the 30 mm dia eccentric shaft
is available it would be  nice to check for clearance to the new spacer.
Please send forwarding  address and cost.

Thank you
John P

I am guessing at the cost.  Perhaps $50 if it is less than that I
will put the change in the box. If  more than that I will eat it. The
largest problem is coming up with a piece  of steel. If my local
supplier has it in stock no problem if not I have to  mail order it
and there may be a minimum. I really big bolt would work. If  you
have a piece of steel we can use that.

Mail address is:
830  East Santa Maria St.
Suite 303  <<<<<<<<<<<<<<very  important
Santa Paula CA
93060

Paul Lamar


I deleted  the photos of the end play spacer and bearing. It looked to me
the
brg ID  was not sufficient for the OD of the spacer. Parts from two series
mixed  up??

Dale Davies

Paul

I have been  able to have a 8.14 mm thickness spacer made which fits the end
play  required per spec.
] don't know how far you have gone on my request for the  thicker spacer. If
it arrived late and not too far in progress then please  return it and
adjust
the costs involved. If already done then so be it with  my thanks.
I earlier tried using the local machine shop to lap grind my  side housings
but he did not have a lapping machine so I sent them to  SC.  After taking
you up on your offer (a bird in hand) I remembered  the local shop does CNC,
lathe work and other machine shop work and he said  he could perform my
request.
I thank you for your offer and am sorry to  cause you unnecessary work.
At any rate have a merry Christmas.

John  P

No problem. What ever it is I'll send it back.
I suspected the  problem was caused by lapping the end housings.

Paul  Lamar

The spacer in the picture appears to be one used behind the oil slinger on
very early engines. Oil slingers are no longer used, as seal performance
has  improved dramatically.

Repeated lapping or even grinding of the irons shortens the engine by a
like amount each time. This has no affect on the end play figure.

However, after a few such grindings the front end of the rear main
bearing may contact the radius on the rear rotor bearing journal.

Since the rear main is moving forward as the engine is shortened and the
crankshaft is not. Alternatively a thin shim may be installed under the rear
stationary gear mounting flange to return needed clearance.

A scraping of the bearing end with a knife blade also eliminates any such
contact.

Lynn E. Hanover

-- 
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Youtube key word PaulLamar2
Copyright 1998-2011 All world wide rights reserved.