I've got a turbo 20B which I have rebuilt twice now. I've sorted
out wiring issues, had Tracy's EC repaired, checked the timing, checked
for fuel and spark; repeatedly.
The engine was, possibly among other things, flooded.
Today I even tried engine starter fluid. I cannot get the
engine to even cough or sputter as if i's even trying to start.
Is there anyone within a reasonable driving distance of Canton,
GA, an hour north of ATL. With Rotary and preferably Tracy EC
experience as well that might consider giving me a visit for
some assistance getting this thing started? I'd be happy to pay
your travel expenses. Ive exchanged numerous emails with Tracy,
this newsletter and Mr. Anderson to no avail. I am at my wits end.
Jay
Ed Anderson might fly in from NC.
Flooding is unlikely for a 20B.
Is the compression now good?
I assume the spark timing has been checked.
Do the injectors squirt?
Do you have a manifold pressure gage on there?
Can you borrow an oscilloscope from some body.
There is also a free program that uses the audio microphone jack
on all PC's as an input to a software O-scope.
Use that to check the CAS. It works great on my Linux machine.
http://www.zeitnitz.de/Christian/scope_en
http://www.picotech.com/picoscope-oscilloscope-software.html
http://www.electro-tech-online.com/general-electronics-chat/38689-
good-cheap -free-pc-oscilloscope-program.html
I do recall reading your emails on this subject.
Send a picture of the intake manifold and injector locations.
Apply 18 volts to the starter. Three 6 volt batteries in series.
Don't let it crank for more than 15 seconds at a time. You
could over heat the starter.
If all else fails I fly UAL (retired A&P wife) for a modest cost
if you could meet me at ATL and provide room and board for a
couple of days. Or I could rent a car. The wife would want to
come along :)
Paul Lamar
Jay - I am in Roswell - less than a half hour away, and would be
willing to help. 770-815-5140
Victor Roberts
Jay,
Start with the basics.....the very basics.
1. Turn off your fuel pumps and leave them off
2. Make sure you have compression. Do two test. One as it sits, then
squirt 20cc of auto trans fluid in each rotor and do another
compression test.
3. Check ignition. Simply pull the plugs out, clamp them for a good ground
and look for spark.
4. Make sure the timing is correct. I prefer an old style timing
light. Also can just make sure rotor 1 is on tdc and the timing mark
lines up on the distributor.
5. If all the above is working and correct, install the plugs, leave
the fuel system off and use a can of carburetor cleaner (berrymans
b12) and spray it in the manifold while cranking. It will fire up
and run if it has compression and correct timed ignition. Do this a
couple of times now just because you've worked so hard to hear
something. Its quite awesome to hear it fire up.
6. Now work on the fuel system.
7. fuel pumps still off, put the system in primer mode, push the primer
button and listen for the injectors to click. It should be easy to
hear. If you do not hear anything theres a problem. Either wiring or
computer. I would bet on wiring.
8. If you do hear the injectors click, pull them out, turn the fuel
pump on and do the same test. They should spray fuel only when
primer is operated and should not leak or drip otherwise. Be careful,
obviously your spraying fuel around. The best way is to put the
injectors in small glass jars.
If all the above is working, your only problem should be mixture.
As a reference. I do not start my 20B in cold start mode. I squirt 6
primes in, turn my mixture knob to full rich, and it fires up every
time. As it warms up I start leaning it out
Hope this helps
Bob Mears
I had a worn out R100 that would not start unless I put a couple table spoons
of oil down the carb. This engine only had 40 pounds compression. When the
revs dropped below 1500 it would stall unless I caught it quick and gave some
throttle. If it stalled at a light I had to get out and pour oil in. Great in
traffic when it started and puked a cloud of oil smoke out. If you have
ignition and fuel spray, try a bit of oil in the intake. Do not need a lot. If
the seals are dry they do not seal well and you end up without enough
compression pressure. Flooded piston engines can sometimes suffer the same way.
Dale Davies
--
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site.
http://www.rotaryeng.net
Youtube key word PaulLamar2
Copyright 1998-2011 All world wide rights reserved.