Subject: Integral prop shaft and planet carrier weight
From: rotaryeng
Date: 1/29/2012, 8:23 AM
To: AAAA Put this in the To box


 This looks real simple. It might be easier than I first thought.
 Getting the roll pins out with Jean's bigger hammer goes a long way
 towards making this viable.

 Paul Lamar


 I love your Rhino illustrations.

 Would there be an easy way to show how the sun-gear shaft/bearings fit
 into this. With some sort of vibration/damper/isolation between the
 rotor-shaft and the sun-gear I find myself puzzled as to how
 everything
 stays where it is supposed to be/

 Robin No name :)


 The same way Tracy does it.

 Paul Lamar


 The weak link so far has been the stock Mazda auto tranny flex plate.
 Ed Carver is working on fixing that as well.

 Paul Lamar

 ...and the pin holding the sun gear to the input shaft.

 Mark

 Yes and that too.


 Paul Lamar


 Thanks for the pics. are you still considering the bellhousing,
 or is it to mount on the front cross-member plate?

 Graeme Riley


 With minor modes it will fit either.

 Here are some weight savings. The shaft and planet carrier combined is
 4.8 pounds. The current Tracy shaft prop flange and ball bearing is
 9.2 pounds perhaps a bit less as Tracy as drilled some holes in the
 flange.

 The housing is 8.7 pounds which is about the same as the current
 Tracy version. Not including a large spacer Tracy uses between the
 housing
 and the motor plate.

 Input shaft and sun gear is 2.4 pounds.

 The ring gear is 4 pounds but almost half of that can be cut off.

 Planet gears, needles, shafts and spacers are .5 pound each for a
 total of 3 pounds.

 Total is 21 pounds less the adapter plate and bolts.

 The auto tranny bell housing is 8.9 pounds. Total about 30 pounds.
 Jeff's motor plate motor mount is 6 pounds less spacers and long 8
 mm bolts so that is pretty much a wash but the bell housing has no
 motor mounts. Motor mounts can weigh as much as 10 pounds over what
 is needed for Jeff's plate.

 This box is going to save about 10 pounds over the current design.
 That has a large effect on the CG as the box is almost the most
 further forward of all masses.

 Paul Lamar


 Paul,I am using a 3.25"  diameter prop shaft on my PSRU  and the oil
 seal is at its maximum RPM limit for recirculating oil and would be over
 the limit for grease.  It has a wiper and a built in  oil reservoir
 between the sealing surfaces.   What will you be using on the 5.10"
 diameter shaft running at propeller speeds? I had considered a slinger
 but  any circumstance that lowers the nose would make a mess and
 contaminate ground water.  I would be interested in a link to a supplier
 that sells something for high speed large diameter shafts.
 George grimes

 The Ceramic bearings are sealed (I think. I hope :)) and are rated for
 14,000 RPM.

 Paul Lamar

 Here is the recent reply from Red Star Bearing:

 "Dear friends, hello!

 Minimum quantity of 10 sets of
 Bearing steel 61821 ceramic ball bearing price: $31.36

 Stainless steel 61821 ceramic ball bearing price: $158.47

 Which country do you come from

 Best wishes

 Red Star Bearing Company Limited Wang Huamin"

 I sent them Henry's address etc, to get the transaction going. Just keeping
 you in the loop.

 Will you be at SZP tomorrow, friday? I may go there to look at some homes.
I
 can bring the tube, and the miged P ports.

 Ed



 Sorry for my ignorance, could someone please explain fatigue load limit on
the bearing chart briefly please,

Graeme Riley

Steel has a stress level below which it will never crack and break.
That is called the fatigue load limit. It varies somewhat with alloy and
heat treat. Shot peening and polishing also helps. This limit can be as low
as 10% of the breaking strength. Aluminum and some other materials have no
fatigue limit. Sooner or later they will crack and break.

That is why aluminum airliners have a cycle life. So many pressurization
 cycles and it is history. So far most composites do not exhibit this
characteristics as far as I can determine. If it don't break it won't break.
Wood is similar.


Paul Lamar


Is that what they call it, Thanks Paul. Didn't know that about wood either,
ya learn something new everyday,sometimes 2 things

Graeme Riley


-- 
The Rotary Engine News Letter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
You Tube key word PaulLamar2
Copyright 1998-2012 All world wide rights reserved.