Subject: First Flight - Turbo Rotary Velocity N17010
From: rotaryeng
Date: 6/9/2012, 11:47 AM
To: AAAA Put this in the To box



June 9, 2002 - A trailer pulled up in front of a simple but comfortable home in Houston.

Lots of trails, tribulations blood, time, money, recreation, education, fun,
friendships, anger, frustration, problem solving, sweat, pondering etc....repeat and
repeat again and again.

Fast forward (it did go fast)

June 9, 2012<x-apple-data-detectors://1> - Ellington Field - A lone, very nervous man
arrives at the airport shortly before 0900 hrs. Pushes onto the ramp the contraption
composed of fiberglass, metal et al and the ingredients listed above. He sits down
and writes a simple holographic (hand written) will and short note with information
to call "Mom" and work. Calls tower to relay intent via the phone.

Preflights the contraption. Gets in, goes though basic Checklist. Cranks up the
engine, which fires right up at about 0920 hrs. Taxi to Juliet. Calls tower to verify
intent and to taxi to active, 35L. Taxis to Taxiway Echo. Checks temps. Pushing 195
with OAT reading 95 degrees (geesh it is only about 0930 hrs).

Cleared to take active and hold. Taxied out. Lined up castering nose wheel down
center stripe. Cleared to take off. Added power and engine smoothly ran up. Airspeed
coming in. 30 kts...50 kts ....60 kts, approximate rotation speed. Lots of runway
(9000 ft).....hold it....70 kts....72 kts... Slight pull on the yoke....AIRBORNE!!!
Leaped into ground effect. Screw this, pulled back on yoke and I am climbing. Jiggled
the yoke a bit to verify control authority.

Climbed to about 400 feet and turned right pattern to crosswind. The Dynon altitude
and airspeed seem to be working. That's reassuring. Pattern altitude is only 600 feet
and I was there already as I turned to downwind. Leveled off and noticed the clouds
were lower than reported and appeared on the ground. Also, noticed coolant temps had
dropped to 190....but oil temps were flashing at me and had reached 225 (synthetic
Royal Purple). Damn. Ok. Fly the airplane, the oil is not at not a critical level. ,
but let's just finish the pattern and land. I grabbed my phone while on downwind and
attempted to record some data but while I can hear the engine the video is
awful....uh, in my defense, I was a bit distracted and way more concerned with
flying. I called the tower and informed them I was coming in. I think they were
looking out for me since as I turned to base I noticed the fire department staged
just off the runways threshold

I noted I was a bit far out on down wind so I stared easing over to turn base. Wow. I
really overshot it as I blew by the runway and had to use full right rudder to get
back to the runway. I wish I had had more rudder. In hindsight I think I was not
using much aileron as I was cognoscente that I had no idea of stall characteristics
so I did not yet wish too strep a turn. I was able to get over the runway and dump
some altitude as I got over the numbers and pulled power. Crap, I am fast. I am lined
up and right on the numbers but at 95 kts. I come and touchdown and bounced. Pulled
power to idles and settled down easily but fast at 90 and rolled out and exited at
Delta. The tower was clearing me back to the city hangars as I was exiting the
active. I taxi back and noticed the oil temps had decreased but I don't recall how
much, just noticed they were lower.

I got back to my hangar and popped the door and shut her down. The engine went silent
without any hissing or gushing.

I called my mom.

I am mowing informing the world.

I did a walk around and did not see anything missing. I am about to pull the cowl and
check things out.

I did notice I did not develop a slight hand shaking until after I landed and exited
the aircraft. ;-) Hey, how about that, it really is an aircraft now. Ten years to the
day following delivery.

Thank you for your support.

Christopher Barber, JD
Houston, Ellington Field (EFD)
Velocity N17010
Turbo Rotary 13b
RWS Re-drive and engine computers
Dynon Skyview
Mistral intake

You made me laugh Chris :)

Congratulations. You are almost there on the oil cooling.

-- The Rotary Engine News Letter. Powered by Linux. ACRE NL web site. http://www.rotaryeng.net You Tube key word PaulLamar2 Copyright 1998-2012 All world wide rights reserved.