Subject: 1st flight renesis P port
From: rotaryeng
Date: 7/8/2012, 10:47 PM
To: AAAA Put this in the To box

Paul,
         [It's] Very quiet!   Actually lifted to weigh. Came in at 1414
lbs with
extensive exhaust system.  Neil.

The CG looks close to perfect.

Paul Lamar


Neil,
I'm very envious!
Herb Karkheck

howdy, folks.  I'm new to this site.  I about 80 hours to go before I
start working on the engine installation.  I've decided on the
Renesis   1st choice, or an older rotary, but definitely a rotary.
I'm working on a Glastar and was startled seeing the spitting image of
it being devoured by a yellow mantis- like thing on Rotary Engine
News.    I've seen the rotary's on barnstormer and really wanted to
buy one, but they seem to be from RV's or pushers, but I need more
info from youse guys who are doing it.   I need some help in knowing
about ;the engine supports specific to the glastar.  If Neil could
give me some direction, I'd appreciate it.  I have Crooks book on the
rotary, but there doesn't seem to be more current literature.  I can't
believe that 200 HP is easily possible, esp with the P intakes.  Very
nice to see so many important parts available,too, for the intake/
exhaust and other important improvements.   I want mine to be extra
quiet also.  I tried to get info from the Sportsman guys in Wash, but
they don;t believe in anything, but the Lycosaurs.  They wouldn't even
tell me why they don't recommend a sub 6; they just say don't.  I'm
believing in the rotary.  How do I get to the forums ?

jz eldorado

Ask away.

Here is another rotary powered Glastar with a Ross GB done about 6 or  7 or
so years
ago by Sigward Ganswindt. Old school plugs up  which dates from 1973  by Lew
Ross RIP.
I have  not heard anything since. I am not even sure if it cooled well.

Paul Lamar

thankyou for the info and pics.  I'm impressed.I'm having a difficult  time
understanding how he packed so much stuff in such a small area.   The  guy
was/is
clever.  are there any pics neils installation, as  that is probably closer
to what
my direction will be.   If that engine  is over 200hp, a little too much
goose of the
throttle, and it will  probably hop off the taxi-way.  where should i go to
start
reading  about the installation process?  I'm wondering if anyone has a plan
for the
engine mount construction?  I'd better start there before I  buy anything.
some of
the engines for sale, tho, have a lot of the  mount assy, and have the
rubber mounts,
too.  I need to do some  reference reading before i ask answered questions,
but how
do you  determine to use the 2.1 or 2.8 GB?  Neil, if you're there, how did
the W&B
look before you  installed the cowling? I'm curious as to  how  far from the
firewall
is the end of the GB. any Pics???

JZ

I do engine mount plans for free.

The distance varies but usually it is around 39 inches.

The 2.8 gear box allows the engine to rev to about 7500 RPM.
Prop RPM is 2630 so the prop tips are subsonic.
That allows a p-port engine to make about 250 HP

Also read this.

http://www.rotaryeng.net/mm-instruct.html


Paul Lamar


Jz Eldorado,
                      All I learned was really was here on this site from
paul, for which I owe a great deal of gratitude.  THe engine mount was
designed by Paul and only slightly modified as necessary to fit.  From
memory Paul's measurement of 39 inches from firewall to prop flange is
correct, but will measure it if concerned.  I have a stock Renesis P ported,
if you are going  Alloy you may have to shift something to keep balance.  My
batteries are under the seats.  Just remember that if you are making engine
mounts that the motor is offset 1.8 degrees to the right and 1.5 degrees
down. My primary muffler is a tangential muffler made by Plane exhaust as
recommended by Paul again and then goes down to be split into two pipes and
two mufflers under the fuse.  Both pipes finish about 2 feet behind the
pilot.   I am averse to flying behind a screaming "Chain saw".  Yes more
drag, but I no longer care.   Glasair are right to steer you away from the
subaru 6 which is what I originally had.  Too heavy plus a few other
problems.  My C of G with the H6 suby was way out the front, putting the
stall speed nearly 10 kts above standard.   Without the cowling the C of G
already looked right with the Rads back under the engine, not way out the
front.  Did all the calcs for the C of G and it is near perfect. I am a very
happy camper.  Have hundreds of photos, but best to get Paul to give you my
email privately if you want to persue this way. Best is really to ask on
this site as many others have better ideas as well.  Neil.
-- The Rotary Engine News Letter. Powered by Linux. ACRE NL web site. http://www.rotaryeng.net You Tube key word PaulLamar2 Copyright 1998-2012 All world wide rights reserved.