Subject: Traditional Megasquirt aircraft problems better
From: rotaryeng
Date: 7/8/2012, 10:25 PM
To: AAAA Put this in the To box


 The Megasquirt was initially rejected for aircraft use as there was
 no method of manually leaning it. The other problem was the
 Megasquirt relies on the O2 sensor to set the mixture. O2 sensors
 are damaged by 100LL. A third problem was the throttle position
 sensor TPS was required.

  As I recall Tracy used these problems years ago as the rational for
 doing his super simple system that uses only manifold air
 temperature MAT/IAT and manifold air pressure MAP to set the mixture
 at any RPM. Therein lies part of the problem tuning Tracy's system.
 Some people have taken a year of flying to get it right.

  The last thing was the Megasquirt rotary engine ignition problem.
 The rotary engine ignition problem could be solved using extra hard
 ware and was solved but it was a messy kludge.

  I agreed with him at the time. That was years (10) before I had the
 idea of using one cheap Megasquirt per rotor. One per rotor is
 likely to eventually simply solve the ignition problem using off the
 shelf computer trigger inductive coils like the LS1 and the RX8
 coils with out using one CD system per plug. One CD system per plug
 is more expensive than a computer triggered inductive coil like the
 LS1 or RX8.

  I know Motorola/FreeScale  68K asm code so in theory I can fix these
  problems by
  recoding the chip.

  Another way of leaning the Megasquirt is trick the MS computer by manually
  adjusting
  the O2 sensor input voltages and simulating the TPS as wide open
 with voltage dividing potentiometers.

  Perry Mick does something like that using a stock RX7 computer and
  probably has over
  1000 hours on it.

  The siren song of the Megasquirt was and still is the built in
 simple EFIS, easy tuning using a note book computer and data logging.

  Time and new technology and new ideas tend to change old rational.

  Paul Lamar

 I've thought about the leaning problem with MS for the past couple years
 sense the issue has come up. Seems you could leave out the O2 sensor
 and replace it with a pot after the running parameters have been programmed.
 Then read your egt for best mix.

 Seems we could also modify the injector dwell time similarly. I have
 a couple MS2 boxes and will loan you one if you like. I'm all for
 using two crank triggers, optical, hall, or whatever for a CD setup.

 Ed Carver

 Yes! I would like to test them Ed. I can come over and pick them up.

 Paul Lamar



 NOTE: You can not replace the O2 sensor with a pot. A pot will vary circuit
resistance. An O2 sensor outputs a voltage of 0V to 1V with 0.5V corresponding
to an air/fuel ratio of 14.7:1; stoichiometric. To accomplish this you would
have to build a circuit to deliver 1V and the pot to reduce to 0.1V as the O2
input. I am not certain how much effect the O2 input will have on the leaning.
It is used as a trim to the fuel delivery calculated from throttle position,
RPM, MAP or MAF. The IAT sensor is also a trim input. It will effect the A/F
ratio but by how much is the question. Only trial will tell if it can lean to
say 18:1.

Dale Davies

Yes if the top of the pot is connected to 5 volts.
I want to find out how much it will lean the mixture.

IAT is no problem. It will work as is.

Paul Lamar
-- The Rotary Engine News Letter. Powered by Linux. ACRE NL web site. http://www.rotaryeng.net You Tube key word PaulLamar2 Copyright 1998-2012 All world wide rights reserved.