Subject: First lift off with single rotor
From: rotaryeng
Date: 7/9/2012, 11:28 PM
To: AAAA Put this in the To box



Cleared the ground for a brief period today. As far as the airplane is
concerned,
everything is good. CG seems to be right on the spot. Much better as it
was 12 years
ago at the first flight with the SOOB.

Here is the reason why it was not a flight. A few days ago when I started
high speed
taxi, as soon as it picked up air speed, the engine started to sputter and
almost cut
out totally. This was at the same RPM as at a run up, where it does not do
that.

With a wiggly tail dragger as the Avid is, there was no way reading enough
instrument
for making a preliminary analysis. I recorded the instrument panel with a
GoPro at
2sec intervals.

Looking at the first pictures, the answer came up right away, increasing
pressure
under the cowl where the intake for the engine is located. Like the EGT
shot up over
1600 just before the sputtering started. Since my radiator air is going to
the
outside of the cowling, there was no impact on cooling. Btw cooling is
really good.
At an OAT of 95F, oil and water stayed at around 170F no matter what I did.

For todays runs, I taped the inlet around the prop hub shut. Sure enough,
the
sputtering occurred at higher airspeed, and was not as total, however, EGT
was still
going to around 1600.

The conclusion is, I have to open the cowling exits a lot.

Richard Sohn
N2071U

http://www.fairpoint.net/~res12/home.html

Congratulations Richard.

Do you have a ram air scoop or cold air box on it?

No pictures came with the message.


I would put a water manometer tap under the cowl to check the intake
pressure for
sure. That carb should not be affected by small changes in ambient air
pressure
unless the vent to the float bowl is plugged. Is there a fuel pressure
regulator in
the system? Tie the tail up in takeoff position and run it up. I assume
the tanks are
in the wings.

1600 EGT is normal at high power. How far is the EGT probe from the port?

I'll be down that way about Oct 1st.

Paul Lamar

Richard,   I don't seem to have a picture of the left side of your
installation but the side view in this post doesn't show an exhaust stack
outside the cowl. It might be that during a static run up the prop blast
vents the exhaust gases but in the dynamics of flight there may be a
reversion back through the cowl to the opening around the spinner
backplate. I assume that at some point you will have a ram air intake
through a heat muff for carb icing which will possibly cure this condition.
      Also congratulations on building your own engine and the airplane as
well.

George grimes

Here is a picture of my intake. No float, but a pressure regulator. The prop
is on the left.

Richard Sohn
N2071U

What brand is that carb? Many of those low pressure carbs have problems with fuel in
high wing tanks. The fuel pressure changes too much with angle of attack. Tie the
tail in the pick up bed and run up the engine to full static RPM.


Paul Lamar

http://www.greatplainsas.com/
Great Plains Logo & Address


HOW TO ADUST POSA STYLE CARBURETORS

IF AFTER FOLLOWING MANUFACTURERS DIRECTIONS, THE ENGINE STILL DOES NOT RUN CORRECTLY.



POSA Style carburetors trace their history back to the late 60's and early 70's. One
of the first carburetors of this style was the Lake Injector. Don't confuse the word
"injector" with fuel injection, as these series of carburetors are not a fuel
injector or fuel injector body. During this same time period the POSA carburetors
were introduced. As the POSA is a casting and the Lakes was a machined product, the
Lake soon disappeared as the POSA was less expensive, buy a large margin.

The POSA was originally sold for aircraft use by HAPI, Revmaster and Monnett
Experimental Aircraft. A little later in history, Revmaster introduced the Revflow
Carburetor which is a similar type carburetor also. It looks like it might be a
modified Lectron Carburetor body, with their own casting on one side of it with
mixture control built into it.

The newest version of the POSA is the Aero Carb. Where as the POSA was a casting, the
Aero Carb is machined from a billet of aluminum. The operational principals of all 4
carbs (Lake, POSA, Revflow and Aero Carb) are identical with variations in mixture
control and needle adjustments for setting the mixture

All of these carbs have different needles that are round but have a flat ground on
one side that is also tapered. As the throttle is opened, the needle is pulled out of
a fuel orifice with the slide, allowing more fuel to be pulled into the carburetor
throat. It is imperative that the flat part of the needle always face into the back
of the carburetor.

If the needle were allowed to rotate, the draw across the needle changes and less
fuel is induced into the engine, causing an engine to run lean. Most manufacturers of
this style carburetor send a number of different needles along with the carburetor.
The needles have different flats ground along the taper, allowing more or less fuel
to be induced to the engine.

This POSA carburetor was originally used on motorcycles. The fuel tank on a
motorcycle has a maximum of about 6" drop from the tank to the carb. On most VW
powered aircraft with a full tank of fuel, there is about 12" maximum fuel drop. The
point being that these styles of carburetors were designed to be operated on gravity
fuel pressure only, and not much at that. I have seen fancy designs for fuel pressure
regulators to be used with return lines etc, but have yet in 30 years seen a
successful installation of a POSA style carb that ran correctly with a pressure
regulator.

A few facts to consider

1" of fuel head is equal to .022 psi

46.17" inches of vertical fuel column is equal to 1 psi

Fuel boils at 170 degrees F

An average engine will consume between .435 and .450 lb. of fuel per hp per hour

Cowling air typically runs 60 F warmer than outside ambient air temperature, with
isolated hotter spots.

A fuel system must have an adequate fuel vent.

Types of carb are float bowl, diaphragm, and floatless

Aircraft carbs, Zenith, Bing, Weber, Solex are examples of float bowl carbs. These
carbs can operate on gravity feed or usually up to 4 psi of fuel pressure. Most of
these have a float bowl well vent to prevent vapor lock.

Tillitson, Ellison, Zama, are types of diaphragm carburetors. These carbs usually
require some fuel pressure to operate correctly.

POSA, Lake Injector, Revflow and Aero Carb are floatless, diaphragm less carburetors.
These carbs do not operate well on more than .5 lbs of fuel pressure; yes that is
less than pound of fuel pressure. These carbs do not vent any fuel vapor that may
form in the body to the venturi as there is not float bowl well or diaphragm vent.

If a vapor lock forms in the body of the carb or the fuel line preceding the carb,
the engine will start to surge and eventually quit if the vapor lock cannot be moved
through the carb. It requires the absence of heat to remove the vapor lock from POSA
style carbs as fuel pumps are not used.

How to adjust the carb for all throttle positions

Tools needed:

Screwdriver

#16 nail ­ sharpened

Small jar

Syringe or breaker graduated in cc's or ounces

Gloves

Small wood throttle blocks (you'll make these)

Fire extinguisher rated for fuel

Instruments needed

Manifold pressure gauge

EGT gauge or air/fuel ratio gauge



So you have followed the manufacturer's directions to adjust your POSA style
carburetor but find that you still have rich or lean spots across the range of
throttle and you're frustrated. The first thing you need to do is acquire some
patience, because to set the carb correctly takes about 4 hours of measuring and tuning.

1. The fuel in the tank should be full. This is because a full tank of fuel will make
the carb run richer and an almost empty tank will run leaner. Remember that you are
operating on .022 pound of pressure per inch of vertical fuel column. So if you have
12" of vertical fuel drop, (this is from the top of the tank to the carb, not from
the top of the tank to the bottom of the tank) with a full tank this is .022 x 12 =
.265 psi or a little over " lb of fuel pressure. For simplicity say our tank is only
6" tall. If we have used a half a tank of fuel we now have used 3" of fuel and have a
9" drop to the carb. So, 9 x .022 = .198 lbs of fuel pressure. Less than a quarter of
a pound.

2. You need to pick 6 throttle positions and be able to repeat the positions. Use
idle, 1500, 2000, 2500, 3000, and wide open throttle. With the carb set as best as
you can get it, make a stop block that you can put in the throttle so you can
accurately repeat each position. The rpm will change when you adjust the carb down
the road. We simply need to be able to repeat the position. I use a piece of wood
that has a hole drilled through it that is the throttle shafts diameter. Split the
piece of wood in the center of the hole. The length of the wood will vary for each
throttle setting.

3. At each throttle setting, use the needle to adjust the carb so the engine runs
that absolute best at each station, irregardless as to how it runs anywhere else.
Make note of the manifold pressure and egt/or air fuel ratio when the carb is set for
each station. Once you have a single station set perfectly with the needle, turn the
fuel on and let fuel flow out of the carb in to the bowl for 1 minute. Measure the
amount and record it next to the egt/air fuel ratio and manifold pressure reading.

4. Repeat step 3 for all 6 stations, recording manifold pressure and rpm along with
egt/air fuel ratio. Measure fuel flow for each individual station and record the
measurement.

Note: this process will consume about 1 gallon of fuel. You need to keep the fuel in
the tank as close to a constant fuel level as possible.

5. Now that you have made a chart that show the fuel flow out of the carb at each
station where you set the carb so that the engine ran it's best, you need to set the
needle so the carb runs the best at idle once aging. This will be the permanent
setting for the needle. Idle position to about 1500 rpm is the most important
throttle range. When you are coming down final you cannot have your engine quit.
Likewise if you need to do a go around, you cannot have your engine stumble when you
advance the throttle.

6. Now go back to each throttle position using your blocks of wood and re-measure the
fuel out of the carb. In most cases it will be less than you originally measured it.
So to bring the fuel flow up the same level you make a vertical mark along the flat
of the needle where the needle goes into the fuel orifice. Just use a black fine line
marker to do this.

Remove the needle. Now use the sharp nail and make a scratch mark along the
horizontal axis of the needle 1/8" on both sides of the vertical mark. When satisfied
with the depth, reinstall the needle and measure the fuel flow. You want it to be
equal to what it was in steps #3 and 4.

This is the trial and error time consuming part of the job. Be cautioned that a
little scratch for starters is better than a deep one. It does not take a very deep
mark to allow a lot more fuel to flow.

When you are done with each station you will have a series of scratched that are not
connected. You may find that in some areas of the needle you won't have to do much
and in others you will have to have a deep scratch and you may need to connect the
scratches with another scratch.

The top and bottom ends are critical. For the top end or wide open throttle, this is
where the egt comes in handy. At wide open throttle, the engine should run about 50
to 100 degrees rich of peak. When you throttle back to 75% (23 inches of manifold
pressure) power the egt should rise. Bear in mind that the rpm's vs. manifold
pressure will be different on the ground than in the air with a loaded propeller.

When set correctly, you should be able to see a steady rise in the egt from idle to
just before full power. At full power, the egt should dip slightly.

When you are in cruise mode with your VW, you want to run at 23" of manifold
pressure, regardless of rpm. This is 75% power and is the best way to tell if you
have the correct prop for your aircraft. Generally, higher speed aircraft like the
KR, Sonerai and Sonex use a 52" to 54" diameter prop. You will usually see a cruise
rpm of about 3000 to 3200 rpm and 23 inches of manifold pressure. Slower aircraft
like the Preceptor Pups, use a diameter of 60" to 62" and corresponding 2800 to 3000
rpm at 23 inches of manifold pressure.

Note: in the event that the needle is rich at the bottom end instead of lean over the
range, you will have to go to the next smallest needle and start the procedure again.
It is very difficult to make a needle leaner with out adding material to the needle.

On POSA style carbs equipped with mixture control, set the mixture control so that is
just shy of being full rich when doing the above needle work. In the event that you
need to make the carburetor slightly richer, you can do so without having to go
through the entire measure, scratch, measure, scratch scenario all over again. As you
burn off fuel, the fuel pressure is less so you may need to go "over rich" to
compensate for less pressure.

The air/fuel ratio meter should read as follows:

Cold start to warm idle 8:1 0 ­ 800 rpm

Idle 12:1 800 ­ 1000 rpm

Mid range 16:1 1000 ­ 2500 rpm

Cruise @23 inches of mp 14:1 2700 to 3300 rpm
Take off 12:1 to 13:1 Wide open throttle

Steve Bennett






-- The Rotary Engine News Letter. Powered by Linux. ACRE NL web site. http://www.rotaryeng.net You Tube key word PaulLamar2 Copyright 1998-2012 All world wide rights reserved.