Subject: 12A engine for sale
From: rotaryeng
Date: 7/10/2012, 11:26 AM
To: AAAA Put this in the To box




 Dear Paul

 While searching Fleabay for something to buy, I saw a 12A engine with dual
 distributors and a 4-barrel carby for sale. I have never seen a rotary
 with 2
 independent distributors, and am seriously considering buying the engine,
 specifically because of this (potential) dual ignition system. Do you know
 these
 engines? It would make a nice little p-port with a dizzy per rotor, and a
 Holly carb
 with leaning block and turbo.

 Erik in Oz.

 As I recall my 1973 12A RX2 had twin distributors. Maybe early RX3 also.
 It was easy
 for Mazda to do that as an off the shelf piston engine distributor would
 work. Only
 the rotor caps were different. Similar to my rational of using one
 megasquirt per
 rotor. The twin distributor front cover will probaly bolt on a 13B. With
 modern
 electronics no distributor is necessary. You can trigger off the front
 pulley or the
 ring gear.


 Nice collectors item if you are restoring an RX2. Only about 120 HP. Not a
 good power
 to weight ratio by todays standards. Not a good aircraft engine as Mazda
 made some
 significant improvements in materials in 1989.

 Paul Lamar

 I don`t think this engine is going to sell, so I plan on offering the
 owner $300 for
 it. I am only looking for around 120 hp. anyway so the plan is to p-port
 it and add a
 carb with a turbo for 140 take-off hp. I am too stupid for fancy
 electronics, anyway.
 Most of the megasquirt discussion you have going at the moment is way over
 my head. I
 like the 2-distributor redundancy and the carby reliability. At least I
 know how they
 work...:)

 If nothing else, I will have a working 120 hp. p-port engine for not too
 much money.
 Would I still find parts for this engine?

 Erik in Oz.


 Rotor housings might be a problem as I think Mazda quit making 12A parts
 quite some
 time ago. Rotor housing are high pressure die castings and very
 technically
 sophisticated and not easy to make. The wear surfaces are chrome plated
 hard steel.

 Regards,

 Erik in Oz.


Hi Paul & All;

I also have a 12A engine I built for a Coot amphibian I was building, But I
gave it up because of getting older and not wanting to mess around in the
water. I sold the airplane parts but the buyer didn't want the engine.

It has the two distributors which makes it easy to set the timing on the two
sets of plugs. I used two TRW Electronic modules  with them. It has a turbo
off a small Buick V8 of the day and it works fine with a poppet type valve
for the control. It also uses a marvel aircraft carb with mixture control.
It has about 30hrs of test running on a test stand on a trailer. The highest
I ever ran it was at 4000 rpm at 40 inches of mp and I thought the trailer
was going to take off. It has a set of gears from a Power Glide trannie with
1.87 reduction. It is easy to get it to run in reverse at the same ratio. I
looked all over for some gears and at the time I couldn't find any thing
better. Dragsters of the day of 1200 hp used those  gearboxes so I thought
they ought to work ok. I worked out a bunch of problems I ran into but I
cured them.

I also have a  Hartzell 92ZK prop hub with SEA-BEE  blades cut down to 74
inches.

If any one is interested just let me know. I have a lot of photos from
building to running.

Regards

BOB San




-- The Rotary Engine News Letter. Powered by Linux. ACRE NL web site. http://www.rotaryeng.net You Tube key word PaulLamar2 Copyright 1998-2012 All world wide rights reserved.