Subject: 12A engine for sale
From: rotaryeng
Date: 7/11/2012, 11:51 PM
To: AAAA Put this in the To box


 Dear Paul

   While searching Fleabay for something to buy, I saw a 12A engine
  with dual distributors and a 4-barrel carby for sale. I have never
  seen a rotary with 2 independent distributors, and am seriously
  considering buying the engine, specifically because of this
  (potential) dual ignition system. Do you know these engines? It
  would make a nice little p-port with a dizzy per rotor, and a Holly
 carb  with leaning block and turbo.

   Erik in Oz.

   As I recall my 1973 12A RX2 had twin distributors. Maybe early RX3
 also.  It was easy  for Mazda to do that as an off the shelf piston
 engine distributor would  work. Only  the rotor caps were different.
 Similar to my rational of using one  megasquirt per  rotor. The twin
 distributor front cover will probaly bolt on a 13B. With modern
 electronics no distributor is necessary. You can trigger off the
 front pulley or the ring gear.

   Nice collectors item if you are restoring an RX2. Only about 120
  HP. Not a good power to weight ratio by todays standards. Not a good
  aircraft engine as Mazda made some significant improvements in
  materials in 1989.

   Paul Lamar

   I don`t think this engine is going to sell, so I plan on offering
  the owner $300 for it. I am only looking for around 120 hp. anyway
  so the plan is to p-port it and add a carb with a turbo for 140
 take- off hp. I am too stupid for fancy electronics, anyway. Most of
 the megasquirt discussion you have going at the moment is way over
 my head. I like the 2-distributor redundancy and the carby reliability.
  At least I know how they work...:)

   If nothing else, I will have a working 120 hp. p-port engine for
  not too much money. Would I still find parts for this engine?

   Erik in Oz.

   Rotor housings might be a problem as I think Mazda quit making 12A
 parts  quite some  time ago. Rotor housing are high pressure die
 castings and very  technically  sophisticated and not easy to make.
 The wear surfaces are chrome plated  hard steel.

   Regards,

   Erik in Oz.

  Hi Paul & All;

  I also have a 12A engine I built for a Coot amphibian I was
 building,  But I gave it up because of getting older and not wanting
 to mess around in the water. I sold the airplane parts but the buyer
 didn't want the engine.

  It has the two distributors which makes it easy to set the timing on
  the two sets of plugs. I used two TRW Electronic modules  with them.
  It has a turbo off a small Buick V8 of the day and it works fine
  with a poppet type valve for the control. It also uses a marvel
  aircraft carb with mixture control. It has about 30hrs of test
  running on a test stand on a trailer. The highest I ever ran it was
  at 4000 rpm at 40 inches of mp and I thought the trailer was going
  to take off. It has a set of gears from a Power Glide trannie with
  1.87 reduction. It is easy to get it to run in reverse at the same
  ratio. I looked all over for some gears and at the time I couldn't
  find any thing better. Dragsters of the day of 1200 hp used those
  gearboxes so I thought they ought to work ok. I worked out a bunch
  of problems I ran into but I cured them.

  I also have a  Hartzell 92ZK prop hub with SEA-BEE  blades cut down
  to 74 inches.

  If any one is interested just let me know. I have a lot of photos
  from building to running.

  Regards

  BOB San

  RX7 Specialties in Calgary, Alberta, Canada makes 12A housings by narrowing
 13B housings. The early housings had a problem with the housings eventually
 compressing in the combustion area and developing a coolant leak
 which let coolant into the combustion chamber. This wet the plugs
 and it would not start.

 Dale Davies

 That is why Mazada  changed to a high silicon alloy around 1989.

 Paul Lamar
 -Paul and Dale

 Would it be as easy as narrowing a 13b housing (on a milling machine,
  I presume)to 12a specs without any other changes?

 Erik in Oz.

 Sounds OK to me. It is only 10 mm off each side as I recall.
 The hard part is you need an NC mill to put in new O-ring slots.
 That is the expensive part. Somebody has to pay the purchase price
 for the NC mill. NC mills are not cheap.

 Paul Lamar

 The total width change is 10mm. RX7 and RX8 housings are 80mm whereas the 12A
housings are 70mm. 5mm off each side will do. The grooves are the trick. High
silicone housings are the benefit. If built with the end housings that have
the o-ring grooves you would not need to machine the grooves in the narrowed
housings. Use the 12A rotors and e-shaft.

Dale Davies


-- The Rotary Engine News Letter. Powered by Linux. ACRE NL web site. http://www.rotaryeng.net You Tube key word PaulLamar2 Copyright 1998-2012 All world wide rights reserved.