The Megasquirt was initially rejected for aircraft use as there was no
method of
manually leaning it. The other problem was the Megasquirt relies on the
O2
sensor to
set the mixture. O2 sensors are damaged by 100LL. A third problem was
the
throttle
position sensor TPS was required.
As I recall Tracy used these problems years ago as the rational for
doing
his super
simple system that uses only manifold air temperature MAT/IAT and
manifold
air
pressure MAP to set the mixture at any RPM. Therein lies part of the
problem tuning
Tracy's system. Some people have taken a year of flying to get it
right.
The last thing was the Megasquirt rotary engine ignition problem. The
rotary engine
ignition problem could be solved using extra hard ware and was solved
but
it was a
messy kludge.
I agreed with him at the time. That was years (10) before I had the idea
of using one
cheap Megasquirt per rotor. One per rotor is likely to eventually simply
solve the
ignition problem using off the shelf computer trigger inductive coils
like
the LS1
and the RX8 coils with out using one CD system per plug. One CD system
per
plug is
more expensive than a computer triggered inductive coil like the LS1 or
RX8.
I know Motorola/FreeScale 68K asm code so in theory I can fix these
problems by
recoding the chip.
Another way of leaning the Megasquirt is trick the MS computer by
manually
adjusting
the O2 sensor input voltages and simulating the TPS as wide open with
voltage
dividing potentiometers.
Perry Mick does something like that using a stock RX7 computer and
probably has over
1000 hours on it.
The siren song of the Megasquirt was and still is the built in simple
EFIS, easy
tuning using a note book computer and data logging.
Time and new technology and new ideas tend to change old rational.
Paul Lamar
I've thought about the leaning problem with MS for the past couple
years
since the issue has come up. Seems you could leave out the O2
sensor and
replace it with a pot after the running parameters have been
programmed.
Then read your egt for best mix.
Seems we could also modify the injector dwell time similarly. I
have a
couple MS2 boxes and will loan you one if you like. I'm all for
using two
crank triggers, optical, hall, or whatever for a CD setup.
Ed Carver
Yes! I would like to test them Ed. I can come over and pick them up.
Paul Lamar
Any time I guess, give me a heads up the night before.
Ed Carver
OK Ed.
Paul Lamar
Hi Paul,
I have been using two MS systems on a 4 cyl
opposed engine for some time, am about to test on a dyno. I run the two
MS with two complete system sensors,ie., TPS, IAT,CYL temp, MAP,
seperate fuel pumps ect.,with RPM triggered from two separate sensors. I
was running using the original ignition system, but one failed so I
upgraded the MS board with a daughter board which enabled me to control
ignition timing, which for me involved relearning how to control the
ignition advance.
The two systems run on the same injectors, two leds on
the dash tell me if both are triggering the injectors,(you can switch
either system off using either the ignition trigger or the power to the
MS system without affecting the running of the engine), BUT, I have not
figured out why when you switch either MS system back on with what you
had switched off the motor runns like SH--t, until you turn off the
system again that you had originally switched off!!
I think it is
something to do with MS on switch on looking at the MAP sensor and maybe
not being able to get a steady voltage from the ignition sensor?? I
reasoned that as the systems were switching the earth on the injectors
that the left hand would not know what the right hand was doing, and it
seems to be the case, except when one switches off one system!!! I have
used the O2 sensor to program the fuel mixture, the thinking was that
I would remove the O2 sensor after programming. I must be missing
something with what people are saying about leaning in flight, surely
that if you have a system that adjusts mixture for altitude, and load
why
would you want to fiddle in flight, after programming the mixture to be
progressively richer at higher and higher manifold pressures, and/or
RPM??
If starting again I would buy the later system with the ignition
controller built in, even if I was not using the ignition part of the
system, the systems are so well assembled (when bought fully assembled)
I do not think it is worth the bother to assemble oneself. MS does not
rely on the O2 sensor to set the mixture, that is set with the VE
tables, you can of course use the Megatune to autotune using the O2
sensor, but i do not know that I would trust it to tune the range of
power/manifold pressures in aircraft in flight.
John Burey
It is one thing to maintain stoichiometric mixture with changes in
altitude and quite
another to lean. Leaning an engine will improve the BSFC at any
altitude and also
at the
expense of power. Most car engines will maintain stoichiometric at all
times.
This is a fundamental difference with aircraft engines. Every licensed
pilot is
taught this.
My implementation of two MS systems on a rotary are entirely
independent.
The rotor one system never tries to control rotor two and vice versa.
Paul Lamar
-
John,
Thanks for relating that experience! But even if your injector was
steady on
as long as the plug was still firing, there was still combustion taking
place in
the combustion chamber instead of the exhaust system unless the
resultant
mixture was just too rich to combust properly...dont know...
Gene Kahn
Hi Gene,
I guess I forgot to say I have 2 spark plugs per
cylinder, so the seperate systems are completly seperate (except for the
injectors), I, when changing the mixture tables, and ignition tables, do
it on one MS system, save then download to the other system keeping them
both the same, (timing and mixture). Then restart the engine on both
systems. There should be a difference when running one spark plug and
one system but there seems not to be a difference, I guess I will notice
it when running on the dyno.
John Burey
Since both MS systems are in parallel on the injector lines, you should
have an isolation diode in each injector wire from the MS to the
injector. Without it, voltage may be backfed into the MS system thru the
injector output circuitry, possibly causing the processor to arrive at
an undetermined state. This could account for the improper operation
when power to the MS is restored, as it may bypass the power-on reset.
Victor Roberts
Thanks Victor, you beat me to it. I would imagine that the driven
components of each system would need to be isolated with a diode so that a
backfeed isn't possible. The results of a backfeed would be unpredictable
at best unless there is a diode somewhere in the circuit inside the MS.
Kevin Alderman
Here is the schematic. For the rotary this can be greatly simplified as most
injectors now a days are not peak and hold.
Paul Lamar
--
The Rotary Engine News Letter. Powered by Linux.
ACRE NL web site.
http://www.rotaryeng.net
You Tube key word PaulLamar2
Copyright 1998-2012 All world wide rights reserved.