http://www.bgsoflex.com/megasquirt.html
Fuel calculations based on mathematical equations and physical formulas relating
directly to your vehicle - many other existing systems rely solely on
trial-and-error, estimation or guesswork for fuel delivery.
All of the embedded microprocessor code executed for MegaSquirt-I™ was
hand-written directly in assembler, not compiled from a high-level language. Working
directly in assembler produces the tightest and fastest-executing code possible, even
compared to the most efficient C compiler available. The result is that MegaSquirt™-I
can provide real-time fuel calculations up to 16,000 RPM!
Electronic Control Unit based on the Motorola MC68HC908GP32 Flash-based micro
controller operating at an internal bus speed of 8 MegaHertz (this is bus speed -
remember that most microprocessors spec their parts at external crystal speed, which
is then divided down by four to yield internal bus speed). Many OEM and popular after
market EFI systems use older processor technology (like the MC68HC11 or Z80) which
operate at 1 or 2 Mhz internal bus speed. The faster clock speed, coupled with direct
assembly-language programming, gives MegaSquirt-I™ its power. Additionally, the
on-chip Flash memory makes this a true single-chip setup, reducing cost and extending
reliability. Also, using Flash technology allows the instant re-programming of
constants, enrichments, etc. while the vehicle is running. - the processor can even
be re-loaded with other control code using a simple programming interface! The flash
can be re-written at least 10,000 times and has a retention duration of 20 years.
Input triggering for injection events is derived from an existing ignition system
- either by connection to a conventional Kettering ignition coil (- terminal) or by
using the TACH signal available from virtually any OEM or aftermarket ignition
system. MegaSquirt uses an on-board opto-isolator to prevent damage due to inductive
kickbacks present on ignition coils. Remember, MegaSquirt only controls fuel, not
ignition. However, we are currently developing a multiple-coil CDI ignition system
with ion-sensing technology which will interface directly to the MegaSquirt system -
stay tuned...
Comments: [This can be as simple as a magnet on the flywheel with with a hall effect
sensor or an Anti lock Brake System sensor or stock Mazda CAS looking at one tit 22
degrees BTDC on the water pump pulley for each rotor. Using one MS 1 per rotor the
injector pulse can be used to fire modern coils like LS1 and RX8 with no software
changes. On a two rotor two sensor are used 180 degrees out. On a three rotor three
sensors are used spaced at 120 degrees out. A small hardware board is required to
condition the injector pulse. An opto isolator will work. P.L.]
Input trigger events (compared to ignition events) can be divided by any number
between one and eight (number of cylinders must be evenly divisible by this injection
number) - this means that there can be an injection event for every ignition event,
or an injection event for every other ignition event (skip one), and so on depending
on selection. The user can switch which injection division number to use while the
car is running - the system will scale the required fuel amount properly on the fly.
Comments:[Probably not needed on the rotary. P.L.]
On most batch injection computer systems, every injector will fire for any
injection event. Megasquirt has two separate injector drivers (discussed below), and
they can be operated in simultaneous mode (both banks fire at the same time) or
alternate mode (the banks fire alternately in a ping-pong fashion) - this allows for
more flexibility in the end-application.
Comments:[Again no needed for the rotary. P.L.]
Two injector drivers are provided to directly operate either saturated or "peak
and hold" injectors. The on-board drivers feature a PWM (Pulse Width Modulation)
current limit mode which is totally under the control of the user - both PWM
application time relative to injection event and duty cycle is adjustable. Virtually
any current-limit amount and time can be programmed, allowing this controller to be
used with pretty much any injector out there.
Comments:[Peak and hold not needed with the Mazda injectors. Two injectors are needed
per rotor and it would be nice if they were staged. P.L]
MegaSquirt® features an on-board Manifold Absolute Pressure (MAP) sensor
(Motorola MPX4115). Having the MAP sensor on-board simplifies installation (one just
runs a vacuum line to the ECU) and keeps the measurement signal clean, which is very
important since the MAP signal is the most critical to proper fuel control. There are
other Motorola MPX-series MAP sensors with expanded scales to handle turbo and
supercharger applications, like the MPX4250A (this sensor handles 3 to 36 psi, or 20
to 250 KPa) - one can swap this sensor in with hardware change. The MAP sensor is
additionally used to obtain the barometric pressure during engine startup, in order
to determine a barometric pressure correction factor (explained below).
Coolant and Air-Temperature sensors are inexpensive (roughly US$9.00) GM units
readily available from any parts store (GM #12146312). These sensors were been used
on practically all GM cars in the 1980's and are easy to find - the same is true for
the correct connectors. Also, the inputs to the ECU for the coolant, MAT, and TPS are
protected from voltage spikes and noise, and there is both hardware and software
low-pass filtering implemented to ensure clean signal measurement. All sensor output
voltages (coolant, MAT and MAP) are converted to engineering units (KPa and degrees
F) in the embedded software using lookup tables. This means that if another sensor is
used, then all one needs to do is generate the transfer function lookup table. These
lookup tables are "included" into the embedded source at compile time
(barofactor.inc, kpafactor.inc, and thermfactor.inc), thus no change to the embedded
control code is required.
MegaSquirt® uses an oxygen sensor as feedback for mixture AFR control. MegaSquirt
is compatible with single wire (unheated - like Bosch Part Number 12014, used
everywhere ) as well as heated units. All parameters that control the feedback (step
size and rate, range, trip threshold voltage) are user-controlled. Additionally,
since the trip point voltage is user-defined, MegaSquirt is compatible with the
DIY-WB (wideband) oxygen sensor board - one simply sets the desired air/fuel ratio
trip voltage and you are there.
Comments:[Disconnect it after tuning to prevent damage from 100LL Lots of Lead. P.L.]
Air density corrections as a function of manifold air temperature (MAT) and
barometric pressure effects on VE are pre-computed as lookup tables and properly used
by the ECU in the fuel calculation. Most aftermarket EFI controllers allow the user
to set the air temperature correction - MegaSquirt-I™ uses the mathematical equation
for air density to generate this correction, so no user intervention is required.
More importantly, many after market EFI controllers do not take account the effect of
barometric pressure change to volumetric efficiency. This correction comes into play
at high altitudes (i.e. low barometric pressures). MegaSquirt® uses a lookup table to
determine this correction, and is consistent with OEM systems.
All enrichment values (i.e. warm up, acceleration, VE, etc) are calculated as
direct percentages and are multiplied together (instead of added). This allows one to
work directly in percentages, which is easy for people to mentally visualize, with
the result that tuning becomes much easier. Adding 25% more fuel is achieved simply
by increasing a quantity by 25. A value of 100% represents the nominal required fuel
for a cylinder - a number less than this represents an enleanment and a value above
this represents an enrichment. Other systems use direct or scaled AFR values or
numbers of unknown or weird units (especially Alpha-N units) - tuning an engine is
difficult enough without having to constantly convert crazy numbers to Air-Fuel Ratios.
There is a 64-point Volumetric Efficiency (VE) table, organized as a conventional
grid eight RPM points vs. eight MAP points. The entries in the VE table are in direct
percentages, so that a number of 80 means that the VE is 80%. You can take direct
dyno VE values and plug them right in without any conversions. Additionally, specific
RPM and MAP range points are adjustable by the end user, a very nice feature. No,
there are not hundreds of VE grid points, only 64 - this allows for plenty of control
of the engine without having to fill in a bunch of grid points with redundant values.
A 16x16-point table (or higher) used by some other units is not a feature, but a
pain, especially during tuning, because all 256 slots need to be entered. In
addition, the value of VE is *correctly* interpolated between grid points and is
truncated to the grid edge points when outside of the table - this is not the case
with other systems on the market.
Comments:[One of the reasons Tracy's system is so hard to tune. P.L.]
There is an output control signal (current sink up to 500 milliamp) designed to
drive an idle bypass solenoid (open/close solenoid, not a stepper), which allows the
addition of more air at idle during warm up. The activation/deactivation temperature
is set by the user.
Comments:[Not needed. P.L.]
A relay drive circuit (up to 500 milliAmps) is provided to control a relay to
power to the fuel pump. Signal is active while the engine is cranking or running, and
will deactivate 2 seconds after the last ignition event.
A nice feature on the MegaSquirt® controller not found on other systems are three
indicator LEDs which reflect the current operating mode of the controller. The first
LED pulses whenever there is an injection event, and the glow duration follows the
actual injector pulse width. The second LED is active whenever the ECU is in a warm
up enrichment state (i.e not at 100%). The third LED indicates an acceleration
enrichment, and is active during the entire duration of the event. Extremely useful,
especially during installation and debug. Flashing lights also look "cool",
particularly when you show off your controller to others.
Comments:[We do not need enrichment during acceleration so no Throttle Position
Sensor is really needed but it might be nice to have. We are not road racing here. P.L.]
The best feature of MegaSquirt® is that you build it yourself! Since you assemble
the controller, and all information about the design is available to you, you are
able to troubleshoot the board if a problem arises, and, in almost all cases, repair
the unit yourself. The system as it exists today is a complete turn-key solution:
solder it together, install in the vehicle, tune, and use. The complete source code
is available on this site for those who want to understand or even modify the control
algorithms - one can convert this board to control nitrous, alcohol, methanol, LPG,
etc. - there is really no limit. Why purchase a $1,000 plus unit when you can build
one yourself?
Last Updated: 01/13/2011 09:43:58
© 2003, 2008 Bowling and Grippo. All rights reserved. MegaSquirt® and MicroSquirt®
are registered trademarks.
--
The Rotary Engine News Letter. Powered by Linux.
ACRE NL web site.
http://www.rotaryeng.net
You Tube key word PaulLamar2
Copyright 1998-2012 All world wide rights reserved.