Subject: Last great idea to use one MS 1 per rotor. Correction.
From: rotaryeng
Date: 7/12/2012, 4:32 PM
To: AAAA Put this in the To box


    Use the injector pulse to fire both LS1 or RX8  coils as well as the
    injector!!.
    These coils have built in switches so they do not need drivers.

    Since the intake port is never fully closed on a p-port rotary, unlike a
    piston
    engine, the injector can operate at 22 degrees BTDC on any rotor.  The
    same time the
    spark plugs are fired.

    It just requires a small board to condition the injector open collector
    pules and
    convert it it to 5 volts. An opto isolator will work.

    No software mods required. With Ed's Carvers mechanical leaning idea
    (changing the
    fuel pressure mechanically) you are good to go.

    I should get a royalty fee for every MS 1 sold to the rotary crowd :)

    Paul Lamar

    Won't work with LS1 or RX8 coils. Must be a CD system. Also use the CAS
  to
    fire the CD system directly. I am still working on the LS1 and RX8 coil
   solution.

    Paul Lamar

    Paul,

   FYI - Back when I first got my 20B I set it up on an engine stand with
 the
   intention of doing some ground running.  Not having the Mazda ignition
   module, or an EC-2,  I modified the CAS with three pickups, spaced 120*
   apart around the inside of the stock CAS housing.  Then I connected the
  CAS
   leads to three GM ignition modules, and fed the outputs to dual tower
   coils, one for each rotor.  I could easily have fed the three signal GM
   ignition module output leads into three MSD CD units, but I was building
  it
   on the cheap, so I used Buick V-6 dual tower coils.  While it didn't have
   spark advance, it did run quite well and was very simple.

   The GM ignition modules are inexpensive and have been "road-tested" in
   millions of GM vehicles.  The GM HEI ignition modules are also a favorite
   of the Jeep crowd.  Might be worth looking into.

   Mark S.

   Thanks Mark.

   I would like to avoid dependency on any OEM ignition system.
   Also the HEI uses the old fashion coils.

   I am with working with the guys at DIY Auto tune to have the MS calculate
   the dwell
   so we can use RX8 coils. It just requires a bit of code addition.
   They may decide to help.

   It was the one MS per rotor that got their attention :)

   BTW using one per rotor gives the computer more time to do extra stuff
   like sending EFIS data to the notebook screen and logging  data on the
   hard disk.

   Paul Lamar

   Paul,

  Couldn't we use the GM HEI ignition module to trigger the LS1 or RX-8
  coils?  I bet one GM HEI module would be able to trigger two LS1's
  providing spark for leading and trailing at the same time.  Fits the KISS
  principle too.

  Mark

  One would think so but what the HEI puts out is an open collector
  transistor
  situation. In other words the coil is grounded by a transistor and the
  other side of
  the primary is connected to 12 volts when it comes time to increase the
  current in
  the coil primary winding and build magnetic energy. Then when the
  transistor turns on
  rapidly the coil magnetic field collapse  causing the coil to spark. The
  transistor
  stays on most of the time causing no current to flow in the primary
  winding.

  http://autorepair.about.com/cs/generalinfo/a/aa052502a.htm

  This transistor is now inside the LS1 and RX8 coils so the situation is
  reversed in
  modern EFI systems.  The computer signal goes high to 5V to build the
  magnetic field
  field and the computer signal goes low to fire.

  That is not to say we could not build a small PC board and put it between
  the HEI and
  the RX8 coil to deal with the situation.


  But why bother. We have less to deal with if we just change the software
  in the mega
  squirt like Tracy does in his system.

  Paul Lamar



 I guess I would need three MS boards.  Doesn't sound like a very cheap
 solution for the 3-rotor guys.  I like the idea of triple redundancy
 though.

 Mark

 The cost will come down. As soon as I get it working on the bench I will
 do a new PC
 board and offer a kit or assembled. I am real excited about this for the
 built in
 EFIS and data logging.

 Paul Lamar

Paul,

Sounds good.  Standing by.

Mark


-- The Rotary Engine News Letter. Powered by Linux. ACRE NL web site. http://www.rotaryeng.net You Tube key word PaulLamar2 Copyright 1998-2012 All world wide rights reserved.