Subject: Traditional Megasquirt aircraft problems better
From: rotaryeng
Date: 7/12/2012, 3:55 AM
To: AAAA Put this in the To box


   The Megasquirt was initially rejected for aircraft use as there was
   no method of manually leaning it. The other problem was the
   Megasquirt relies on the O2 sensor to set the mixture. O2 sensors
   are damaged by 100LL. A third problem was the throttle position
   sensor TPS was required.

    As I recall Tracy used these problems years ago as the rational for
   doing his super simple system that uses only manifold air
   temperature MAT/IAT and manifold air pressure MAP to set the mixture
   at any RPM. Therein lies part of the problem tuning Tracy's system.
   Some people have taken a year of flying to get it right.

    The last thing was the Megasquirt rotary engine ignition problem.
   The rotary engine ignition problem could be solved using extra hard
   ware and was solved but it was a messy kludge.

    I agreed with him at the time. That was years (10) before I had the
   idea of using one cheap Megasquirt per rotor. One per rotor is
   likely to eventually simply solve the ignition problem using off the
   shelf computer trigger inductive coils like the LS1 and the RX8
   coils with out using one CD system per plug. One CD system per plug
   is more expensive than a computer triggered inductive coil like the
   LS1 or RX8.

    I know Motorola/FreeScale  68K asm code so in theory I can fix these
    problems by
    recoding the chip.

    Another way of leaning the Megasquirt is trick the MS computer by manually
    adjusting
    the O2 sensor input voltages and simulating the TPS as wide open
   with voltage dividing potentiometers.

    Perry Mick does something like that using a stock RX7 computer and
    probably has over
    1000 hours on it.

    The siren song of the Megasquirt was and still is the built in
   simple EFIS, easy tuning using a note book computer and data logging.

    Time and new technology and new ideas tend to change old rational.

    Paul Lamar

   I've thought about the leaning problem with MS for the past couple years
   sense the issue has come up. Seems you could leave out the O2 sensor
   and replace it with a pot after the running parameters have been programmed.
   Then read your egt for best mix.

   Seems we could also modify the injector dwell time similarly. I have
   a couple MS2 boxes and will loan you one if you like. I'm all for
   using two crank triggers, optical, hall, or whatever for a CD setup.

   Ed Carver

   Yes! I would like to test them Ed. I can come over and pick them up.

   Paul Lamar



   NOTE: You can not replace the O2 sensor with a pot. A pot will vary circuit
 resistance. An O2 sensor outputs a voltage of 0V to 1V with 0.5V corresponding
 to an air/fuel ratio of 14.7:1; stoichiometric. To accomplish this you would
 have to build a circuit to deliver 1V and the pot to reduce to 0.1V as the O2
 input. I am not certain how much effect the O2 input will have on the leaning.
 It is used as a trim to the fuel delivery calculated from throttle position,
 RPM, MAP or MAF. The IAT sensor is also a trim input. It will effect the A/F
 ratio but by how much is the question. Only trial will tell if it can lean to
 say 18:1.

 Dale Davies

 Yes if the top of the pot is connected to 5 volts.
 I want to find out how much it will lean the mixture.

 IAT is no problem. It will work as is.

 Paul Lamar

    Hi  Paul,
                    One has to use a wide band O2 sensor, old style
narrow band are almost impossible to chase the mixture, do not ask how I
know,:'( , also be careful about exhaust temperature will kill the
sensor stone dead very quickly, also do not ask how I know that little
gem! Your info says 850 deg C mine said 950 deg C, I think your temp limit
is more like the real death temp. I had it fitted at the junction of the
headers, about 2.5 ft from the heads, but I had the exhaust tubes
wrapped, with heat tape, so probably the temp. was still much the same
as at the head, the EGT was showing about 1200F sensors are about 2"
from head.
       John Burey

Since a wide band O2 sensor is externally heated you can place them near the end of
the exhaust system after the exhaust gases get a chance to cool off. It is not a good
idea the wrap rotary headers as the temp is too high to the point the headers might fail.

Of course you cannot use O2 sensors of any kind with 100LL aviation fuel.
LL stands for Lots of Lead :)

Paul Lamar

-- The Rotary Engine News Letter. Powered by Linux. ACRE NL web site. http://www.rotaryeng.net You Tube key word PaulLamar2 Copyright 1998-2012 All world wide rights reserved.