Subject: Traditional Megasquirt aircraft problems better
From: rotaryeng
Date: 7/12/2012, 9:43 PM
To: AAAA Put this in the To box


 The Megasquirt was initially rejected for aircraft use as there
  was no
    method of
    manually leaning it. The other problem was the Megasquirt relies
  on the O2
    sensor to
    set the mixture. O2 sensors are damaged by 100LL. A third problem
  was the
    throttle
    position sensor TPS was required.

    As I recall Tracy used these problems years ago as the rational
  for doing
    his super
    simple system that uses only manifold air temperature MAT/IAT and
  manifold
    air
    pressure MAP to set the mixture at any RPM. Therein lies part of the
    problem tuning
    Tracy's system.  Some people have taken a year of flying to get it
  right.

    The last thing was the Megasquirt rotary engine ignition problem.
  The
    rotary engine
    ignition problem could be solved using extra hard ware and was
  solved but
    it was a
    messy kludge.

    I agreed with him at the time. That was years (10) before I had
  the idea
    of using one
    cheap Megasquirt per rotor. One per rotor is likely to eventually
  simply
    solve the
    ignition problem using off the shelf computer trigger inductive
  coils like
    the LS1
    and the RX8 coils with out using one CD system per plug. One CD
  system per
    plug is
    more expensive than a computer triggered inductive coil like the
  LS1 or
    RX8.

    I know Motorola/FreeScale  68K asm code so in theory I can fix these
    problems by
    recoding the chip.

    Another way of leaning the Megasquirt is trick the MS computer by
  manually
    adjusting
    the O2 sensor input voltages and simulating the TPS as wide open
  with
    voltage
    dividing potentiometers.

    Perry Mick does something like that using a stock RX7 computer and
    probably has over
    1000 hours on it.

    The siren song of the Megasquirt was and still is the built in
  simple
    EFIS, easy
    tuning using a note book computer and data logging.

    Time and new technology and new ideas tend to change old rational.

    Paul Lamar

        I've thought about the leaning problem with MS for the past
  couple years
        since the issue has come up. Seems you could leave out the O2
  sensor and
        replace it with a pot after the running parameters have been
  programmed.
        Then read your egt for best mix.

        Seems we could also modify the injector dwell time similarly.
  I have a
        couple MS2 boxes and will loan you one if you like. I'm all
  for using two
        crank triggers, optical, hall, or whatever for a CD setup.

        Ed Carver

        Yes! I would like to test them Ed. I can come over and pick
  them up.

        Paul Lamar

      Any time I guess, give me a heads up the night before.

      Ed Carver

      OK Ed.

      Paul Lamar

    Hi   Paul,
      I have been using two MS systems on a 4 cyl
    opposed engine for some time, am about to test on a dyno. I run
  the two
    MS with two complete system sensors,ie., TPS, IAT,CYL temp, MAP,
    seperate fuel pumps ect.,with RPM triggered from two separate
  sensors. I
    was running using the original ignition system, but one failed so
 I   upgraded the MS board with a daughter board which enabled me to control
    ignition timing, which for me involved relearning how to control the
    ignition advance.

    The two systems run on the same injectors, two leds on
    the dash tell me if both are triggering the injectors,(you can
  switch
    either system off using either the ignition trigger or the power
  to the
    MS system without affecting the running of the engine), BUT, I
  have not
    figured out why when you switch either MS system back on with what
  you
    had switched off the motor runns like SH--t, until you turn off
 the   system again that you had originally switched off!!

    I think it is
    something to do with MS on switch on looking at the MAP sensor and
  maybe
    not being able to get a steady voltage from the ignition sensor??
 I   reasoned that as the systems were switching the earth on the injectors
    that the left hand would not know what the right hand was doing,
  and it
    seems to be the case, except when one switches off one system!!! I
  have
    used the O2 sensor to program the fuel mixture, the thinking was
  that
    I would remove the O2 sensor after programming. I must be missing
    something with what people are saying about leaning in flight,
  surely
    that if you have a system that adjusts mixture for altitude, and
  load why
    would you want to fiddle in flight, after programming the mixture
  to be
    progressively richer at higher and higher manifold pressures, and/
  or RPM??

    If starting again I would buy the later system with the ignition
    controller built in, even if I was not using the ignition part of
  the
    system, the systems are so well assembled (when bought fully
  assembled)
    I do not think it is worth the bother to assemble oneself.  MS
  does not
    rely on the O2 sensor to set the mixture, that is set with the VE
    tables, you can of course use the Megatune to autotune using the
 O2   sensor, but i do not know that I would trust it to tune the
 range of   power/manifold pressures in aircraft in flight.      John
 Burey

    It is one thing to maintain stoichiometric mixture with changes in
  altitude and quite
    another to lean. Leaning an engine will improve the BSFC at any
  altitude and also
  at the
    expense of power. Most car engines will maintain stoichiometric at
  all times.
    This is a fundamental difference with aircraft engines. Every
  licensed pilot is
    taught this.

    My implementation of two MS systems on a rotary are entirely
  independent.
    The rotor one system never tries to control rotor two and vice
  versa.

    Paul Lamar
    -

    John,
    Thanks for relating that experience!  But even if your injector
  was steady on
    as long as the plug was still firing, there was still combustion
  taking place in
    the combustion chamber instead of the exhaust system unless the
  resultant
    mixture was just too rich to combust properly...dont know...
    Gene Kahn

      Hi  Gene,
                      I guess I forgot to say I have 2 spark plugs per
  cylinder, so the seperate systems are completly seperate (except for
  the
  injectors), I, when changing the mixture tables, and ignition
  tables, do
  it on one MS system, save then download to the other system keeping
  them
  both the same, (timing and mixture). Then restart the engine on both
  systems. There should be a difference when running one spark plug
 and one system but there seems not to be a difference, I guess I
 will notice it when running on the dyno.                John Burey

  Since both MS systems are in parallel on the injector lines, you
  should
  have an isolation diode in each injector wire from the MS to the
  injector. Without it, voltage may be backfed into the MS system thru
  the
  injector output circuitry, possibly causing the processor to arrive
 at an undetermined state.  This could account for the improper operation
  when power to the MS is restored, as it may bypass the power-on reset.

  Victor Roberts

 John, Victor, Paul and all...thanks for your help!  I would be
 interested
 in adding a second independent leading plug to each rotary
 combustion chamber since we dare not depend on just a trailing plug
 [see prior thread on red hot exhaust systems!], and I appreciate
 Victor's
 circuitry planning for failure mode for 2 plugs.  Mazda's LeMans engine
 had 2 lead plugs per rotor [plus the trailing plug for 3 total per
 rotor]...
 but I am guessing they used a different rotor housing casting.  The
 second leading plug might be positioned close enough to the first one
 [perhaps near the leading plug, and between the leading and trailing
 plug, giving three plugs total per chamber], that the flame front still
 works with the existing rotor face design.  I will investigate this
 with an
 old rotor housing.  If I am barking up the wrong tree someone can
 feel free to set me straight.  Meanwhile, I will take a close look
 at my housing to inspect the coolant passages, and then make a slice
 or two through the housing to get a better look at what metal might
 be available for another plug etc.

 I am also planning on being at Mazdatrix on Monday morning August
 20th and will ask them about this and other things.  If anyone has
 anything else specific they would like me to ask, please let me know.

 Gene Kahn


 No, not two leading plugs. One leading, one trailing and one FAR trailing.
One thing to look at would be to drill into the housing beside the leading
plug on both sides. Don't drill through the housing all the way. Machine the
surface on the inside of the inner contour flat and square.Use a drill press
to chuck up a piece of high silicone Al and spin it fairly fast. The idea is
to fuse the turning rod to the rotor housing. Then the outside can be welded
to the outside of the housing. Then the spark plug holes can be machined in
giving dual leading plugs. Leave a plug in the old leading hole or machine an
Al plug to fill it the leaves minimum space to loose compression.

Dale Davies


-- The Rotary Engine News Letter. Powered by Linux. ACRE NL web site. http://www.rotaryeng.net You Tube key word PaulLamar2 Copyright 1998-2012 All world wide rights reserved.