Subject: New Megasquirt mother board rotary
From: rotaryeng
Date: 7/16/2012, 7:08 PM
To: AAAA Put this in the To box


I've always been an indifferent programmer, and I have 0 experience with 68 asm. I
could probably muddle through it and end up with something that works though. Are you
looking for someone to make modifications to the MS source?

I've been thinking, and it may make more sense to use something like the TPS input.
MS has a neat built in tuning feature if you hook up a wideband. It would be a shame
to give up that capability. The TPS on the other hand probably isn't necessary for AC
use as it is mostly concerned with throttle response.  I am assuming that you have no
other inputs that are unused in your setup.

Josh

Mostly for some one to collabrate. Two heads are better than one. Most of the time
the other guy has a better idea :) I have got to come up with a routine that
calculates the coil dwell time compensation as a function of RPM. The idea is turn on
the current in the coil 2 or 3 ms before you need the spark to fire.

We can connect the O2 sensor as long as you are running no lead auto gas.
A switch somewhere can turn it off and on. 100LL destroys O2 sensors.

We got 8 channels of A to D and we are using only six.

Paul Lamar



    I've run wideband sensors on cars with leaded race gas for considerable time with
    little ill effects.  To be sure, eventually the lead will coat the sensor, but if
    you're only using it for tuning, you can remove it once you're finished and plug the
    bung.

    Isn't there some built in dwell time compensation in the ms software? I was using the
    ms+spark-extra version. Have you checked that one out? It was several years ago, they
    may have integrated it with the baseline ms by now.

    http://www.msextra.com/doc/index.html#ms1

    http://www.msextra.com/doc/ms1extra/MS_Extra_Basic_Configuration_Manual.htm#rotary

    Josh


    Thats what I had in mind. By rearranging the chips I am going to wind up with a lot
    of real estate left over. The cost will be lower as well. Use of the CD4050 buffer
    instead of transistors  helps a lot as well.

    Yes on the dwell but I haven't found the source code yet. I suspect that was done in
    C version. I have to support this so I am sticking with asm.

    Paul Lamar

   Paul,

   Open this file and search for "dwell".  They've noted it fairly well.
   I can't make heads or tails of the actual programming without studying
   asm.

   Josh


   I did and this is what I came up with.
    ldhx    #0
 sthx    dwelldelay1
 sthx    dwelldelay2
 sthx    dwelldelay3
 sthx    dwelldelay4
 sthx    dwelldelay5
 sthx    dwelldelay6

   Aha they used a look up table.

   clrlowresH    ; low res (0.1ms) timer
 clrlowresL  ;
 ldadwellcrank_f
 stadwelldms ; initial dwell period
 mov#$10,dwellush ; } high speed dwell delay,
   ; default of 4.1ms
 clrdwellusl ; } until calc in main loop
 bset    SparkLSpeed,SparkBits   ; At boot turn on low speed ignition
 clrRevLimBits

   From the looks of it they struggled with the problem a bit :)

   They are using a timer that increments or decrements every .1ms. Probably what
   happens is they preset the counter in the timer as a function of RPM. Low count low
   RPM. High count high RPM I think Then the timer interrupts the back ground program to
   fire the plugs when it times out. Presto bingo.

   Thanks Josh. I think I got it.

   Here is how the Timebase Module works in the MC68HC908 :
   Quote the MC68HC908 data sheet.

 Paul Lamar
   ----------------------------------------------------------
   Timebase Module (TBM)
   16.1 Introduction
   This section describes the timebase module (TBM). The TBM will generate periodic
   interrupts at user selectable rates using a counter clocked by the external crystal
   clock. This TBM version uses 15 divider stages, eight of which are user selectable.

   16.2 Features
   Features of the TBM module include:

   • Software programmable 1-Hz, 4-Hz, 16-Hz, 256-Hz, 512-Hz, 1024-Hz, 2048-Hz, and
   4096-Hz periodic interrupt using external 32.768-kHz crystal (We have)

   • Configurable for operation during stop mode to allow periodic wakeup from stop
   16.3 Functional Description

   NOTE
   This module is designed for a 32.768-kHz oscillator. (that is what we are using)

   This module can generate a periodic interrupt by dividing the crystal frequency,
   CGMXCLK. The counter is initialized to all 0s when TBON bit is cleared. The counter,
   shown in Figure 16-1, starts counting when the TBON bit is set. When the counter
   overflows at the tap selected by TBR2:TBR0, the TBIF bit gets set.

   If the TBIE bit is set, an interrupt request is sent to the CPU. The TBIF flag is
   cleared by writing a 1 to the TACK bit. The first time the TBIF flag is set after
   enabling the timebase module, the interrupt is generated at approximately half of the
   overflow period. Subsequent events occur at the exact period.

   -------------------------------------------------------------------------
   End of quote.

   Piece of cake :) If I get this working that will allow using cheap LS1 or RX8 coils.
   MSD CD's are expensive. Thanks for your help Josh.

   Paul Lamar

 Josh,

 I think they use a dwell time delay timer to start the actual dwell
 angle. So higher rpm actually uses less delay, and lower rpm should be
 more delay.

 Years ago I got totally confused when I first found "timing" used in
 relation to "angle".

 Since engine is mechanical, but ignition is electronic, they actually
 live on two different "time" domain. Mechanical devices base all
 timing on distance traveled. Therefore, its timing is based on angle
 traveled, rather than time as in seconds or fractions thereof.

 Since ignition coil needs time "K ms" to build up its energy content,
 when translated to mechanical timing in degrees, we have to change the
 amount of degrees in order to get a consistent K. Thus the advance in
 Dwell angle at higher rpm to keep "K" a constant time to charge up the
 coil.

 The timer routing uses absolute time. Each revolution has a variable
 amount of time depending on RPM. As RPM goes up, time becomes less. To
 get the proper Dwell Angle, or a fixed time of K, we have to calculate
 the time needed for a revolution at a given RPM, then subtract the
 necessary Dwell Angle Time "K" to get the Dwell delay timer. I think
 you are pointing to the Dwell delay timer thus the reason why it is
 should be smaller at higher rpm.

 Hope this makes sense and may be useful when someone tries to tune
 their engine. As I think this is also true for fuel injection timer.

 Henry Nee

 Hi Henry,
 How's it going. I am thinking of coming over there for awhile. How much would an
 apartment  cost me in Shenzhen by the month?


 Here is a simple QB program that calculates the numbers.

 CLS
 PRINT "RPMRPS  Ms Per Rev    Deg per Ms "
 FOR RPM = 2000 TO 8500 STEP 500
 RPS = RPM / 60
 MsPerRev = 1000 / RPS
 PRINT USING "####"; RPM;
 PRINT USING "######.###"; RPS;
 PRINT USING "#######.###"; MsPerRev;
 DegPerMs = 360 / MsPerRev
 PRINT USING "#########.#"; DegPerMs
 NEXT

 Also check out the attached table file. The trouble with the Mac is they don't
 automatically display attached files so you missed this table in my last message :)

 Paul Lamar



Hey Paul,

Here's an annotated perl translation.  You can run this on your Linux box.

 Mark LaPierre
------------------------------------------------------------------------------
#! /usr/bin/perl
#
# DwellTimer
#
# This program calculates time/angle data
# for rotating objects.
#
# VERSION	DATE		PROGRAMMER	COMMENT
# 1.0		2012/07/16	mlapier		Initial issue.

use strict;
use warnings;

my $MsPerRev;
my $DegPerMs;
my $Rpm=2000;
my $RPM;
my $RPS;

# CLS
system("clear");

# PRINT "RPM     RPS       Ms Per Rev    Deg per Ms "
printf "%-8s %-10s %-14s %-10s\n", "RPM", "RPS", "Ms Per Rev", "Deg per Ms";

# FOR RPM = 2000 TO 8500 STEP 500
until( $Rpm > 8500 ) {

	# RPS = RPM / 60
	$RPS=$Rpm / 60;

	# MsPerRev = 1000 / RPS
	$MsPerRev=1000 / $RPS;

	# DegPerMs = 360 / MsPerRev
	$DegPerMs=360 / $MsPerRev;

	# PRINT USING "####"; RPM;
	# PRINT USING "######.###"; RPS;
	# PRINT USING "#######.###"; MsPerRev;
	# PRINT USING "#########.#"; DegPerMs
	printf "%-8d %-10.3f %-9.3f %9.1f\n", $Rpm, $RPS, $MsPerRev, $DegPerMs;

	# NEXT
	$Rpm+=500;
}

-------------------------------------------------------------------
-- The Rotary Engine News Letter. Powered by Linux. ACRE NL web site. http://www.rotaryeng.net You Tube key word PaulLamar2 Copyright 1998-2012 All world wide rights reserved.