I think I am running into limitations of the MC68HC908.
I think I need another timer module for the dwell calcs.
Since I am doing another board anyway I am thinking putting a
faster and better processor on it.
Not much different in cost and some of the later Megasquirt asm
programs will work. The same processor is used on the daughter
card. However there is other stuff on the daughter card we don't
need. GM stepper IAC control not needed. CANBus communications for
interface with GPIO Board, IO Extender, or other devices.
DIYautotune wants $199 for the daughter card but you still have to
pay another $250 for the mother board.
Why not? Just a few extra bucks for the processor. $10 total
roughly. You can never have enough I/O. http://tinyurl.com/755wdzh
The MC9SC64 has no ROM in it. You flash the whole program in it.
It has 64K flash and 4K RAM.
Here is a list of feature.
-----------------------------------------------------------------------------------------
----------------------------------------------------
Paul Lamar
I'm for the better processor. Like you said, you can never have too
many I/O's... especially if you foresee integrating an EFIS, etc.
Josh
The software for that is already done. Both in the megasquirt and
the PC. Over the years a tremendous amount of work has been done. It
pays to take advantage of that.
Paul Lamar
G'day Paul, Josh
I 'm totally out to lunch when it comes to EFI but I have a few
points/questions
1. does an o2 sensor adjust the fuel to acheive clean burning ( to
pass smog laws) or does it just give us a reading? This may foil our
efforts to adjust AFR for lean burn and best power.
2. if the sensor is clogged by solid lead accumulation, perhaps we
could move the pick-up out of the direct airflow by placing it in a
recessed position or behind a shroud/deflector. this will still
analyze the exhaust but protect it from lead accretion.
So I thought I would search to see if I could find a lead safe O2
sensor and found this info. I reckon that this may mean more to you
Paul than I.
http://www.factorypro.com/dyno/dyno_ec997,eddycurrent,mc,dynamometer.html.
Also try the links at the bottom of the page.
Maybe if we used a TPS that would shift AFR to best power at wot and
best economy below 75%. Or perhaps different power maps as the race
boys use for power/economy modes. Back to you.
Graeme Riley
1. Usually the O2 sensor system are set to stoichiometric or about
14.7:1 air fuel ratio. It depends on what kind of smog you are
talking about. If you are talking about NOx yes this gives a low
smog number but at a severe fuel burn penalty. Lean burn high NOs
gives a better BSFC. Long story but here is a bit about it. B. Bruce-
Biggs. The War Against the Automobile. Dutton. 1977 book explains it
the best. Don't get me started :)
2. They might be one to something.
http://tinyurl.com/cps7v2o
Paul Lamar
In OEM EFI systems, the target is 14.7:1. The O2 sensor responds to the O2 in
the exhaust and develops a corresponding voltage. This is a low voltage; 0 to
1 volt. 14.7 corresponds to 0.5V. In a properly operating EFI, the computer
tries to hold the O2 volts to 0.5. It does this by increasing and decreasing
the pulse width to the injectors according to the O2 input. It does this many
times per second. On a scan tool or some electronic dashes you can pull up X
counts or cross counts which is the number of times per second the voltage
crossed the 0.5V threshold. The higher the count the better.
I falls under the category of "trimming" like the coolant temp sensor and IAT
sensor. Basic fuel delivery is calculated from the TPS, RPM and MAP or MAF
sensor inputs.
Lead in the exhaust will be everywhere and coats the sensor surface so the
chemical reaction that causes the voltage output can not take place.
Dale Davies
--
The Rotary Engine News Letter. Powered by Linux.
ACRE NL web site.
http://www.rotaryeng.net
You Tube key word PaulLamar2
Copyright 1998-2012 All world wide rights reserved.