Subject: heater outlet and oil hose size
From: rotaryeng
Date: 7/21/2012, 9:26 PM
To: AAAA Put this in the To box


  Where do I connect the small 1" hose outlet used for the heater in
     the car?  What type of hose should I use for the oil lines?
   Thanks   for any help Joe Berki

      The nipple for the heater is on the top of the rear(car) end housing.

      AN8 or AN10.

      Paul Lamar

     Paul,
     Does this heater hose connection get blocked off or does it get
     plumbed into the system?

     Joe Berki

     Block it off if you don't have a heater on a pusher. On a tail
     dragger vent it back to the water pump. Here is a jpg from my
  book.   How to Cool your Wankel.

     Paul Lamar

     1"?? Most auto heaters have 5/8" hose from the thermostat housing
  (engine  side) to the heater and 3/4" return to the water pump
  suction. Some use both as 5/8". That looks like a de aeration vent
  to the surge tank.

    Dale Davies

    Helps to fill the block as the engine is tilted up in a tail
   dragger. You get a big air bubble in there.

    Paul Lamar

   Paul,

   We ought to differentiate between the small 1/4" port on the top of
  the rear side housing and the larger 5/8" (?) port just below the
  oil filter pad.  We typically use the 1/4" port for an air bleed
  back to the swirl tank, and the 5/8" port for a cabin heater, if
  used, otherwise just block it off.  I wouldn't want to route it back
  to the water pump as this is heated water.  If anything, I would
  route it to the inlet side of the radiator.

   BTW, it isn't easy blocking the 5/8" port off as it is an oddball
   size, and there isn't enough material to drill it out to the next
   larger size.  I ended up cleaning it thoroughly and then filling the
   nipple with Devcon.

   Mark S.

   You are absolutely right.
   However the output part of the water pump is the inlet side of the
   rad :)

   Paul Lamar

   Correct me if I am wrong but does the water pump suction come from
  the cool part of the radiator and the pump out pressurize the block?

  Dale Davies

  Yes.
  It is more like the pressure is constant in the entire system.
  There may be a small pressure drop across the pump but we use a 30
  psi pressure cap to raise the boiling point.

  What is rather confusing about the 13B Mazda water pump is both
  inlet and outlet of the block water jacket goes through the pump body.

  The pump is built into the front cover on the RX8.

  Paul Lamar


  Being a Journeyman mechanic I realize the cooling system is pressurized by
the expansion of the coolant as it warms up. Once at operating temperature and
stabilized, there is no more pressure increase. The coolant pump is the
circulation "generator".

Dale Davies

Yes and the faster it circulates the better. The rate of heat transfer from metal to
coolant gets better as the flow speed gets faster. Common sense. The bigger the fire
hose the faster it puts out the fire.

The real way to measure the engine temperature is place a thermal couple close to the
combustion chamber near the lower spark plug. The metal temperature must be kept
below 500 F or 260 C in any aluminum engine. CHT.

Don't go on the water temperature alone. It takes a 3 HP pump to get enough water
speed. When I first found the restriction in the 13B water pump back about 2002 and
published the modification to eliminated it on here apparently Mazda engineering was
listening.  They removed the restriction  in the RX8 water pump design. The RX8 WP
gearing and impellor size is about the same as the 280 HP turbo 13B RX7 engine but no
restriction.

BTW an electric water pump is not going to cut 3 HP.
1 hp is 746 watts. Three HP is 2238 watts. At 14 volts that is 160 amps! assuming
100% eff. Nobody makes an off the shelf electric pump that uses 160 amps.
Been there and done that.

http://www.rotaryeng.net/electric-water-pumps.html


Paul Lamar


A more familiar concept may be wind chill.  Everyone understands that
the harder the wind blows the colder it feels.  That's because it's
carrying away heat from our skin at a faster rate.  That's why we all
know to blow on a bite of hot food before putting it in our mouth or to
sit in front of a fan when the weather is hot.

Air is just another fluid.  The same principles that explain wind chill
also apply to coolant fluid inside the engine and, in correlation,
inside the radiator except that the heat is flowing into the coolant
inside the engine and out of the coolant inside the radiator.  The
faster the fluid flow the faster the heat is removed by the coolant.
Faster flow causes increased turbulence which mixes the hot fluid
touching the hot surface with the cooler fluid flowing by outside the
boundary layer reducing the thickness of the boundary layer.

The boundary layer acts like insulation.  We all understand that thicker
insulation is more effective at reducing heat flow than a thinner layer
of similar insulation.  You more often hear about delta T, the
difference in temperature between the air in the system and the
temperature of the heat exchanger surface, in air conditioning systems
than you do in engine cooling systems.  Mixing of heated coolant in the
boundary layer with cooler coolant outside the boundary layer increases
the delta T between the coolant at the surface and the inside surface of
the engine block resulting in faster heat transfer and better cooling.

Any of you ridden a motor cycle at highway speed in hot weather?  As the
air temperature increases the relative wind against your skin begins to
feel hot instead of cool.  When the air temperature exceeds your skin
temperature the heat starts to flow in the opposite direction heating
you up instead of cooling you off.  And you thought that dude on the
bike in the hot summer weather was enjoying the nice cool breeze.  NOT!

Mark LaPierre


-- The Rotary Engine News Letter. Powered by Linux. ACRE NL web site. http://www.rotaryeng.net You Tube key word PaulLamar2 Copyright 1998-2012 All world wide rights reserved.