Subject: New Megasquirt mother board rotary MC9S12C64
From: rotaryeng
Date: 7/22/2012, 2:22 PM
To: AAAA Put this in the To box


 I think I am running into limitations of the MC68HC908.
  I think I need another timer module for the dwell calcs.
  Since I am doing another board anyway I am thinking  putting a
 faster and better processor on it.

  Not much different in cost and some of the later Megasquirt asm programs
  will work.
  The same processor is used on the daughter card. However there is other
  stuff on the
  daughter card we don't need. GM stepper IAC control not needed. CANBus
  communications
  for interface with GPIO Board, IO Extender, or other devices.

  DIYautotune wants $199 for the daughter card but you still have to pay
  another $250
  for the mother board.

  Why not? Just a few extra bucks for the processor. $10 total
 roughly. You can never have enough I/O.  http://tinyurl.com/755wdzh

  The MC9SC64 has no ROM in it. You flash the whole program in it.
  It has 64K flash and 4K RAM.

  Here is a list of feature.


-----------------------------------------------------------------------------------------

  ----------------------------------------------------

  Paul Lamar

   I'm for the better processor.  Like you said, you can never have
 too  many I/O's... especially if you foresee integrating an EFIS, etc.

   Josh

   The software for that is already done. Both in the megasquirt and
 the PC.  Over the years a tremendous amount of work has been done.
 It pays to take advantage  of that.

   Paul Lamar

  G'day Paul, Josh
  I 'm totally out to lunch  when it comes to EFI but I have a few
  points/questions

  1. does an o2 sensor adjust the fuel to acheive clean burning ( to
  pass smog laws) or does it just give us a reading? This may foil our
  efforts to adjust AFR for lean burn and best power.

  2. if the sensor is clogged by solid lead accumulation, perhaps we
  could move the pick-up out of the direct airflow by placing it in a
  recessed position or behind a shroud/deflector. this will still
  analyze the exhaust but protect it from lead accretion.
  So I thought I would search to see if I could find a lead safe O2
  sensor and found this info. I reckon that this may mean more  to you
  Paul than I.

  http://www.factorypro.com/dyno/dyno_ec997,eddycurrent,mc,dynamometer.html.

  Also try the links at the bottom of the page.
  Maybe if we used a TPS that would shift AFR to best power at wot and
  best economy below 75%. Or perhaps different power maps as the race
  boys use for power/economy modes. Back to you.
   Graeme Riley

  1. Usually the O2 sensor system are set to stoichiometric or about 14.7:1
  air fuel
  ratio. It depends on what kind of smog you are talking about. If
 you are talking about NOx yes this gives a low smog number but at a
 severe fuel burn penalty. Lean burn high NOs gives a better BSFC.
 Long story but here is a bit about it.
  B. Bruce-Biggs. The War Against the Automobile. Dutton. 1977 book
 explains it the best. Don't get me started :)

  2. They might be one to something.
  http://tinyurl.com/cps7v2o

  Paul Lamar

  1. If you're using a wideband O2 sensor, Megasquirt can adjust the
  fuel to any target AFR that you specify.  I believe you can even
  specify different AFRs in a MAP vs RPM table so that you can target
  different afr's in different situations.  If you're using the narrow
  band variety, it can target 14.7:1 only.  In either case, the AFR
  "seeking" function is optional.  You can have it just give the
  readout.

  2. I'm not sure if shielding the sensor would help with lead
  accumulation or not.  It would be interesting to see if it works.

  Josh

  The new chips  are surface mount and a lot smaller. I was never really
  fond of DB
  connectors for aircraft use anyway. Ten times easier to wire. What
 do you guys think of a smaller, lower cost board with these connectors?

  This board is 3.9 inches by 2.5 and is stackable. One rotor, two
 rotors, three rotors or four. The heat sink on the top will double
 as a spacer. In and out are separate. Input on the left and output
 on the right.

  Paul Lamar

  I believe there is a similar connector that is 2 piece. The base is
 pins, the top mating connector has the screw terminals. Makes
 servicing easier, instead of having to unscrew each individual wire,
 just pop off the top piece. Stands up just fine to vibrations, very
 snug mate, but easy to add a locking device, if it makes you feel
 better. Used in industrial applications everywhere.
  C. Smith

  I have seen those.
  I have some space limitations. I can get 3 PC boards for $50 if
 they are no larger than 2 X 3.8 inches. The terminal strips are on
 3.5 mm centers. Thats .137 inches. Here is the latest version of the
 board. It has the best features of MS 1 and MS II. It is able to run
 the latest software as it uses the powerful $10 MC9S12 chip. We just
 don't need half the crap that comes with the latest Megasquirt
 boards like CAN, 8 cylinder injection and stepper motor drivers.

  Not done yet but I will have a little real estate left.

  Paul Lamar

  As far as I can tell, they will have the same footprint on the
 board. Will look for the PN as soon as I can find one in the hangar,
 or get back to work on Wed.
  C. Smith

  Is this it? Ost plug and socket. 0.15 inch pitch.
  These are getting extremely popular. There are a zillion on the market.
  How well does the plug lock in to the header?

  "TE Connectivity's AMP brand products
  - TE Connectivity AMP, formerly Tyco Electronics AMP is the world's
 leader in the development and manufacture of a wide variety of
electronic/electrical
  connectors and
  interconnection systems."

  Are you still in Michigan?

  Paul Lamar

  That looks very similar. The type I had in mind has the pin strip at
  vertical to the
  board, and the conductors 90deg out. It is a widely used style of
  connector in
  industrial applications. Many manufacturers have their own
 variations. The ones I have experience with are AMP manufactured,
  and the plug is quite secure. takes a fair amount of force to pull
 apart, and the pull has to be well aligned with the pin axis. Have
 never seen one that was properly seated come apart on it's own. Not
 a lock, per se, but a good deal of friction. A better method of
 termination would be to tin the copper, then a sleeve of heat shrink
 over the transition from tinned to copper to insulation for support.

  No longer in MI, have relocated to Louisville. Hangar on Bowman field.
  Building new Escape.
  C. Smith

 Paul,
    I have no real amount of experience in what I am talking about
 but..........
 I have seen a lot of debate over "proper aircraft quality wiring"
 and have to assume that it is indeed an important subject. I see the
 advantages of these connectors but they are industrial and not
 aviation. Years ago in my first RX7 I was a little too assertive in
 pulling the connector out of the MAF sensor. My father, who was an
 electrical engineer working in radar, navigation and weapons control
 systems for the Canadian government trouble shot the MAF and after
 removing the potting material discovered that a small wire had
 broken at a solder joint. Even though he was very experienced in
 this sort of work he refused to do the repair himself , instead
 sending it to Halifax to a colleague who was recognized as being the
 best at this sort of detailed work. Apparently he recognized the
 importance of skill.

    It seems to me that there are going to be several  single piont failure
 modes here regardless of how we go about making the connections so I
 wonder if we are wise to not use the safest industry recognized
 connection method available. Does Robin  know of any aviation based
 connectors ? I am interested in experimental aviation but not
 experimental electronics. I would hate for rotaries to fall out of
 the sky because of something like an industrial connector or an
 automotive hose clamp.

 John

 There is nothing wrong with industrial connectors for use on
 aircraft as all the parts are soldered on the PC board as well. In
 many cases the industrail environment is severe.

 Look in any avionics box sold and you will see the same thing.
 Normal procedure is to support the parts so they do not vibrate at
 the frequencies and accelerations they are likely to see in a
 general aviation aircraft. Many use DB connectors with soldered
 wires supported by heat shrink tubing.

 According to NASA we are doing better by crimping the wires in these
 connectors. However you are free to use AN connectors if you wish
 but you will still have to solder or crimp the wires to the AN
 connectors and use heat shrink.

 One can also use vibration isolators to shock mount the EFI system.
 I shock mounted Tracy's computer in the RV4 using these mounts.

 BTW the smooth rotary engine goes a long way to reduce the
 frequencies and accelerations the avionics devices are likely to see.

 Paul Lamar

 With regard to vibration; early Detroit Diesel 2 stroke engines with the DDEC
electronic controls had the ECU mounted on the side of the engine block. They
eventually developed a problem which was traced to the PROM chip moving around
in the electrical connectors and developing a poor connection. The chip
retention was the same as automotive with plastic clips. Their solution was a
plastic plate, spacers and longer machine screws. The plastic clips were
removed and three screws on the board. The plate was set over the PROM chip
with the spacers and screws. This way it could not move around. The cylinder
block of an engine is a fairly high vibration place even on the 2 strokes
which had balance weights on the cams and ran quite smoothly. The inline 6, 4
strokes that are a fairly well balanced design inherently also run with out a
lot of vibration. BUT it is there to demolish sensitive equipment.
 The ECU mounted on the rubber isolators in the passenger cabin will not be
subject to a lot of vibration.


Dale Davies



-- The Rotary Engine News Letter. Powered by Linux. ACRE NL web site. http://www.rotaryeng.net You Tube key word PaulLamar2 Copyright 1998-2012 All world wide rights reserved.