Subject: New Megasquirt mother board rotary MC9S12C64
From: rotaryeng
Date: 7/22/2012, 2:20 PM
To: AAAA Put this in the To box


 I think I am running into limitations of the MC68HC908.
    I think I need another timer module for the dwell calcs.
    Since I am doing another board anyway I am thinking  putting a
 faster and better   processor on it.

    Not much different in cost and some of the later Megasquirt asm
 programs will work.   The same processor is used on the daughter
 card. However there is other stuff on the   daughter card we don't
 need. GM stepper IAC control not needed. CANBus communications   for
 interface with GPIO Board, IO Extender, or other devices.

    DIYautotune wants $199 for the daughter card but you still have
 to pay another $250   for the mother board.

    Why not? Just a few extra bucks for the processor. $10 total
 roughly. You can never   have enough I/O.  http://tinyurl.com/755wdzh

    The MC9SC64 has no ROM in it. You flash the whole program in it.
    It has 64K flash and 4K RAM.

    Here is a list of feature.


-----------------------------------------------------------------------------------------

    ----------------------------------------------------

    Paul Lamar

   I'm for the better processor.  Like you said, you can never have
 too  many I/O's... especially if you foresee integrating an EFIS, etc.

   Josh

   The software for that is already done. Both in the megasquirt and
 the PC.  Over the years a tremendous amount of work has been done.
 It pays to take advantage  of that.

   Paul Lamar

    G'day Paul, Josh
    I 'm totally out to lunch  when it comes to EFI but I have a few
 points/questions

 1. does an o2 sensor adjust the fuel to acheive clean burning ( to
 pass smog laws) or does it just give us a reading? This may foil our
 efforts to adjust AFR for lean burn and best power.

 2. if the sensor is clogged by solid lead accumulation, perhaps we
 could move the pick-up out of the direct airflow by placing it in a
 recessed position or behind a shroud/deflector. this will still
 analyze the exhaust but protect it from lead accretion.
 So I thought I would search to see if I could find a lead safe O2
 sensor and found this info. I reckon that this may mean more  to you
 Paul than I.

 http://www.factorypro.com/dyno/dyno_ec997,eddycurrent,mc,dynamometer.html.

 Also try the links at the bottom of the page.
 Maybe if we used a TPS that would shift AFR to best power at wot and
 best economy below 75%. Or perhaps different power maps as the race
 boys use for power/economy modes. Back to you.
   Graeme Riley

 1. Usually the O2 sensor system are set to stoichiometric or about
 14.7:1 air fuel ratio. It depends on what kind of smog you are
 talking about. If you are talking about NOx yes this gives a low
 smog number but at a severe fuel burn penalty. Lean burn high NOs
 gives a better BSFC. Long story but here is a bit about it. B. Bruce-
 Biggs. The War Against the Automobile. Dutton. 1977 book explains it
 the best. Don't get me started :)

 2. They might be one to something.
 http://tinyurl.com/cps7v2o

 Paul Lamar

 1. If you're using a wideband O2 sensor, Megasquirt can adjust the
 fuel to any target AFR that you specify.  I believe you can even
 specify different AFRs in a MAP vs RPM table so that you can target
 different afr's in different situations.  If you're using the narrow
 band variety, it can target 14.7:1 only.  In either case, the AFR
 "seeking" function is optional.  You can have it just give the
 readout.

 2. I'm not sure if shielding the sensor would help with lead
 accumulation or not.  It would be interesting to see if it works.

 Josh

 The new chips  are surface mount and a lot smaller. I was never
 really fond of DB connectors for aircraft use anyway. Ten times
 easier to wire. What do you guys think of a smaller, lower cost
 board with these connectors?

 This board is 3.9 inches by 2.5 and is stackable. One rotor, two
 rotors, three rotors or four. The heat sink on the top will double
 as a spacer. In and out are separate. Input on the left and output
 on the right.

 Paul Lamar

 I believe there is a similar connector that is 2 piece. The base is
 pins, the top mating connector has the screw terminals. Makes
 servicing easier, instead of having to unscrew each individual wire,
 just pop off the top piece. Stands up just fine to vibrations, very
 snug mate, but easy to add a locking device, if it makes you feel
 better. Used in industrial applications everywhere.
 C. Smith

 I have seen those.
 I have some space limitations. I can get 3 PC boards for $50 if they
 are no larger than 2 X 3.8 inches. The terminal strips are on 3.5 mm
 centers. Thats .137 inches. Here is the latest version of the board.
 It has the best features of MS 1 and MS II. It is able to run the
 latest software as it uses the powerful $10 MC9S12 chip. We just
 don't need half the crap that comes with the latest Megasquirt
 boards like CAN, 8 cylinder injection and stepper motor drivers.

 Not done yet but I will have a little real estate left.

 Paul Lamar

 As far as I can tell, they will have the same footprint on the
 board. Will look for the PN as soon as I can find one in the hangar,
 or get back to work on Wed.
 C. Smith

 Is this it? Ost plug and socket. 0.15 inch pitch.
 These are getting extremely popular. There are a zillion on the market.
 How well does the plug lock in to the header?

 "TE Connectivity's AMP brand products
 - TE Connectivity AMP, formerly Tyco Electronics AMP is the world's
 leader in the development and manufacture of a wide variety of
 electronic/electrical connectors and interconnection systems."

 Are you still in Michigan?

 Paul Lamar


 They seem to lock in fairly well. They work well in areas of low or no
vibration. I would be hesitant in locations of vibration. That said, they are
used in Murphy panels for compressor engine/plant control. These are usually
smaller compressor systems, and seem to have fairly low problem occurrence.
Tightening the set screws puts pressure on the wires. Not tight enough and
they can fall out. To tight and you cut the wires. And of course vibration
causes them to flex at the junction and fatigue eventually. Proper tie down of
the wires helps prevent this.

Dale Davies

The wires, where they go into the screw down terminal blocks, have solid bronze gold
plated pins. These are crimped on the ends of the wires and secured with heat shrink
tubing. These pins are unlikely to break.

Paul Lamar
-- The Rotary Engine News Letter. Powered by Linux. ACRE NL web site. http://www.rotaryeng.net You Tube key word PaulLamar2 Copyright 1998-2012 All world wide rights reserved.