Subject: New Megasquirt mother board rotary MC9S12C64
From: rotaryeng
Date: 7/22/2012, 7:27 PM
To: AAAA Put this in the To box


 I think I am running into limitations of the MC68HC908.
     I think I need another timer module for the dwell calcs.
     Since I am doing another board anyway I am thinking  putting a
  faster and better   processor on it.

     Not much different in cost and some of the later Megasquirt asm
  programs will work.   The same processor is used on the daughter
  card. However there is other stuff on the   daughter card we don't
  need. GM stepper IAC control not needed. CANBus communications   for
  interface with GPIO Board, IO Extender, or other devices.

     DIYautotune wants $199 for the daughter card but you still have
  to pay another $250   for the mother board.

     Why not? Just a few extra bucks for the processor. $10 total
  roughly. You can never   have enough I/O.  http://tinyurl.com/755wdzh

     The MC9SC64 has no ROM in it. You flash the whole program in it.
     It has 64K flash and 4K RAM.

     Here is a list of feature.


-----------------------------------------------------------------------------------------

     ----------------------------------------------------

     Paul Lamar

    I'm for the better processor.  Like you said, you can never have
  too  many I/O's... especially if you foresee integrating an EFIS, etc.

    Josh

    The software for that is already done. Both in the megasquirt and
  the PC.  Over the years a tremendous amount of work has been done.
  It pays to take advantage  of that.

    Paul Lamar

     G'day Paul, Josh
     I 'm totally out to lunch  when it comes to EFI but I have a few
  points/questions

  1. does an o2 sensor adjust the fuel to acheive clean burning ( to
  pass smog laws) or does it just give us a reading? This may foil our
  efforts to adjust AFR for lean burn and best power.

  2. if the sensor is clogged by solid lead accumulation, perhaps we
  could move the pick-up out of the direct airflow by placing it in a
  recessed position or behind a shroud/deflector. this will still
  analyze the exhaust but protect it from lead accretion.
  So I thought I would search to see if I could find a lead safe O2
  sensor and found this info. I reckon that this may mean more  to you
  Paul than I.

  http://www.factorypro.com/dyno/dyno_ec997,eddycurrent,mc,dynamometer.html.

  Also try the links at the bottom of the page.
  Maybe if we used a TPS that would shift AFR to best power at wot and
  best economy below 75%. Or perhaps different power maps as the race
  boys use for power/economy modes. Back to you.
    Graeme Riley

  1. Usually the O2 sensor system are set to stoichiometric or about
  14.7:1 air fuel ratio. It depends on what kind of smog you are
  talking about. If you are talking about NOx yes this gives a low
  smog number but at a severe fuel burn penalty. Lean burn high NOs
  gives a better BSFC. Long story but here is a bit about it. B.
 Bruce- Biggs. The War Against the Automobile. Dutton. 1977 book
 explains it the best. Don't get me started :)

  2. They might be one to something.
  http://tinyurl.com/cps7v2o

  Paul Lamar

  1. If you're using a wideband O2 sensor, Megasquirt can adjust the
  fuel to any target AFR that you specify.  I believe you can even
  specify different AFRs in a MAP vs RPM table so that you can target
  different afr's in different situations.  If you're using the narrow
  band variety, it can target 14.7:1 only.  In either case, the AFR
  "seeking" function is optional.  You can have it just give the
  readout.

  2. I'm not sure if shielding the sensor would help with lead
  accumulation or not.  It would be interesting to see if it works.

  Josh

  The new chips  are surface mount and a lot smaller. I was never
  really fond of DB connectors for aircraft use anyway. Ten times
  easier to wire. What do you guys think of a smaller, lower cost
  board with these connectors?

  This board is 3.9 inches by 2.5 and is stackable. One rotor, two
  rotors, three rotors or four. The heat sink on the top will double
  as a spacer. In and out are separate. Input on the left and output
  on the right.

  Paul Lamar

  I believe there is a similar connector that is 2 piece. The base is
  pins, the top mating connector has the screw terminals. Makes
  servicing easier, instead of having to unscrew each individual wire,
  just pop off the top piece. Stands up just fine to vibrations, very
  snug mate, but easy to add a locking device, if it makes you feel
  better. Used in industrial applications everywhere.
  C. Smith

  I have seen those.
  I have some space limitations. I can get 3 PC boards for $50 if they
  are no larger than 2 X 3.8 inches. The terminal strips are on 3.5 mm
  centers. Thats .137 inches. Here is the latest version of the board.
  It has the best features of MS 1 and MS II. It is able to run the
  latest software as it uses the powerful $10 MC9S12 chip. We just
  don't need half the crap that comes with the latest Megasquirt
  boards like CAN, 8 cylinder injection and stepper motor drivers.

  Not done yet but I will have a little real estate left.

  Paul Lamar

  As far as I can tell, they will have the same footprint on the
  board. Will look for the PN as soon as I can find one in the hangar,
  or get back to work on Wed.
  C. Smith

  Is this it? Ost plug and socket. 0.15 inch pitch.
  These are getting extremely popular. There are a zillion on the market.
  How well does the plug lock in to the header?

  "TE Connectivity's AMP brand products
  - TE Connectivity AMP, formerly Tyco Electronics AMP is the world's
  leader in the development and manufacture of a wide variety of
  electronic/electrical connectors and interconnection systems."

  Are you still in Michigan?

  Paul Lamar

  They seem to lock in fairly well. They work well in areas of low or
 no vibration. I would be hesitant in locations of vibration. That
 said, they are used in Murphy panels for compressor engine/plant
 control. These are usually smaller compressor systems, and seem to
 have fairly low problem occurrence. Tightening the set screws puts
 pressure on the wires. Not tight enough and they can fall out. To
 tight and you cut the wires. And of course vibration causes them to
 flex at the junction and fatigue eventually. Proper tie down of the
 wires helps prevent this.

 Dale Davies

 The wires, where they go into the screw down terminal blocks, have
 solid bronze gold plated pins. These are crimped on the ends of the
 wires and secured with heat shrink tubing. These pins are unlikely
 to break.

 Paul Lamar


 The way you describe the connection is good and reliable. Dumb oil field
sparks that use the insulated pins with too much insulation stripped or that
do not use the pins and just jab the wire in, is a problem. That is the
difference between FIGs and FEGs.

Dale Davies

-- The Rotary Engine News Letter. Powered by Linux. ACRE NL web site. http://www.rotaryeng.net You Tube key word PaulLamar2 Copyright 1998-2012 All world wide rights reserved.