Subject: megasquirt rotary ignition
From: rotaryeng
Date: 7/27/2012, 6:35 PM
To: AAAA Put this in the To box


  I have thought about it and thought about it and I have come to the
  conclusion the
  best way to do it is in hardware. The MC68HC908 does not have the
  additional timer
  needed to do it in software.

  This uses a CMOS 555 pulse width generator to generate a pules width that
  will delay
  a 3 ms one shot to fire LS1 coils and RX8 coils. These coils will overheat
  and fail
  if the dwell is much longer than 4 or 5 ms. I have tested all these
  circuits and the
  CMOS 555 pulse width generator works extremely well. Much better than my
  wildest
  expectations. It works the same way the 555 EFI system works.

  The RPM parameter is in the form of an analog voltage. In other word an
  analog tach.
  It is a simple circuit that generates a DC voltages when fed with a
  constant pulse
  width depending on the RPM. Basically a resister and capacitor.  High RPM
  more
  voltage low RPM less voltage.

  This is fed into the CMOS 555 to generate a varying pulse width delay. Low
  RPM long
  delay. High RPM short delay. Therefor the signal is reversed by an
  inverting op amp.
  The whole rig is triggered about 50 degrees BTDC.

  Here is the preliminary circuit.

  I'll do a bunch of tiny PC boards and sell them. You can buy the parts
  from digikey.

  Paul Lamar



  On 07/27/2012 08:00 AM, DIYAutoTune.com Sales (Matt) wrote:
  If you want to do something like this, you're on your own - I don't see it
  having any
  advantage over using the MS2/Extra dedicated spark control features. I
  don't really
  understand why you're doing this, and if you want my advice in the matter,
  I would
  recommend just going with the MS2/Extra rotary settings.

  Thanks,

  Matt Cramer

  MS2extra is way overkill for our purposes, way too complicated, with way
  too many add
  on/plug in cards and way too expensive. The MS 1 version 2.2 is perfect
  for our
  purposes except for the lack of ignition. Besides that the MS2 Extra is
  programed in
  C. C is not my cup of tea. I like to know exactly what the program is
  doing,
  precisely what it is doing and exactly how long the program takes to do it.
  I also takes a lot of time doing software and it is never bug free.

  This cheap circuit (less than $50 including the PCB) also works with carbs
  and LS1 or
  RX8 coils. It has adjustable dwell times and advance rate with out
  rewriting the
  software program.

  The attached pdf is the first documented embedded use of a single chip
  computer as
  far as I can find. If anybody can come up with one that was done and
  documented
  earlier I would like to know about it. I am not talking about home
  computer toys
  with keyboards and crt displays.

  BTW I have been on my own ever since I was 15 years old  in 1950 :)

  Paul Lamar


  I'll take two thank you.
  C. Smith


 I will take 2 also,

 Kevin Alderman


Paul,

Put me down for 2.  If one were to use the existing 3rd gen timing wheel  where would
the sensor need to be mounted?
Appreciate your efforts.

Joe Berki

You should make a new sensor wheel or use the flex plate.

It will need to fire rotor one an two about 50 degrees BTDC.

You will need two pickups. Either CAS types or Hall Effect.


Paul Lamar

-- The Rotary Engine News Letter. Powered by Linux. ACRE NL web site. http://www.rotaryeng.net You Tube key word PaulLamar2 Copyright 1998-2012 All world wide rights reserved.