Subject: Whitecourt World River Boat Races
From: rotaryeng
Date: 8/16/2012, 2:28 PM
To: AAAA Put this in the To box


 There is a couple of people from OZ and NZ in Whitecourt this weekend
 for
 the
 World River Boat Races. Great show! $5 to get into the river boat
 park. Up
 to
 140 MPH on the water. Lots of noise and water spray.
 Dale Davies
 Any rotaries?
 Paul Lamar
 "Any rotaries". In case any of you didn't know, I am the director of a
 non-profit ocean research group, Pelagic-Research.org. We use our boats
 to
 take research groups to catch, tag and study sharks. I am working on the
 design for a boat specifically for our work- It will be approximately 30
 feet long, will have a removable transom and be powered by a pair of
 rotary
 engines shafted to jet drives. We need the jet drives so that the sharks
 and researchers can't be injured by props. We need the transom removed
 so
 that we can pull sharks onto the deck and 3 minutes later send them back
 without lifting or handling them unnecessarily.
 We are collecting funding for the project, and I have a couple of hulls
 picked out that can be modified for our purpose. I will post pics as the
 project takes shape. I am projecting 200 HP per engine, with a pair of
 engines. We are targeting next summer as the splash date.
 For the question of why the rotary- here is the reasoning:
 Jet drives like high speed, and run well in the 4500 to 6000 RPM range.
 The engines have to fit under the deck- the rotaries are small. The
 whole
 package has to be compact, and produce good power with reasonable fuel
 economy. For comparison we used a 250 HP 2 stroke outboard running at
 4500
 RPM which typically burns 14 to 15 GPH. Our goal with this boat is to be
 able to get 30 knots on 15 GPH or less.
 We typically spend a week or more offshore on our trips, and fuel
 stations
 are scarce at best. On top of that, I absolutely refuse to carry
 hundreds
 of gallons of gasoline in our main vessel partly because we sleep on it,
 partly because we don't have gasoline tanks on our all diesel boat. The
 small boat has to be able to carry it's own fuel sufficient for the
 trip. The "mother ship" uses 20 gallons per hour idling and 80 gph under
 way, and takes a crew of 3 just to move it. So, we will tow the smaller
 boat out, use it for the running and shark tendering, and tow it back.
 For those that are counting, that will be 3 engines that I intend to use
 the EFI on. I really don't like carbs on a plane, and I especially don't
 like them under the deck of my boat.
 I am collecting parts for engines in the boat, and any spare parts that
 you
 have would be appreciated. We are a listed non profit in Florida, but
 for
 some reason it seems to be taking the IRS longer to list us as tax
 exempt.
 Go figure.
 Kevin Alderman
 I ran a few numbers to get an idea of the BSFC for the outboards.
 14 GPH is 87.5 pounds per hour at 6.25 pounds per gallon.
 If you divide that by 250 HP you get a BSFC of .35. Too low by a
 factor of .6. Two cycle engines are usually .6 BSFC or higher.
 My guess is you are only using 145 HP while you are getting that fuel
 burn. What do you guess the throttle opening is on the outboard?
 At full power on the outboard at .6 BSFC you would be burning 150 pounds
 per hour or 24 gallons per hour.
 I would nail things down a bit better by connecting a manifold pressure
 gage
 to one of the outboards and record that and the RPM to see the amount
 of HP you are using to go X fast.
 The rotary, at partial power, leaned is .47 BSFC.
 Therefor the rotary at 145 HP will burn 68 to 69 pounds per hour or 11
 GPH.
 At full power (250 HP) and a BSFC of .5 for the rotary 20 GPH.
 At full power (200 HP) and a BSFC of .5 for the rotary 16 GPH.
 Here is a HP and BSFC chart for the Le mans p-port 4 rotor.
 The dotted line is leaned.
 I think Dave Atkins sells a Marine water cooled exhaust manifold.
 Paul Lamar
 As far as BSFC on the outboard, no we were not at WOT. Your guess at 140
 or
  so is probably about right, cruise on plane. I ran the numbers because on
  the way in we ran out of fuel. The owner of the boat said that there was
 no
  way that we were out, but the numbers do not lie, and upon removing the
  sending unit from the top of the tank the bottom of the tank was clearly
  visible. Out of gas.

  We do not plan to run our research boat as a speedboat, but it is nice to
  have power available, however a 4 rotor likely wouldn't fit in the space
 we
  have available below the deck. Its primary use is to patrol a 2 mile
 radius
  around the mother ship looking for and dealing with sharks.Since much of
  our time is spent at lower throttle settings just easing around (2500 rpm
  or so) I will likely go with a Renesis and leave it with standard ports
 and
  NA.

  The water cooled exhaust is always welcome :)

  Kevin Alderman

  I am not advocating a 4 rotor. I just used that to illustrate what BSFC
 you are
  likely to get. It applies to all rotaries. 1,2,3 or 4 rotors. The RX8
 engine is no
  better at higher power levels. It just scores well at idle and low RPM.

  I thought water cooled exhaust was mandated by the Coast Guard.

  Paul Lamar

 Actually, water cooled exhaust is optional. We can always run a dry stack
 vertically if we want. Matter of fact, the Coast Guard 47' motor lifeboat
 has dry manifolds. Only wrapped with turbo insulation tape. The engines are
 Detroit Diesel 6v 92 turbo with v drives.

 Kevin Alderman

 Maybe it is just California lakes.

 Paul Lamar


Cant speak to California, its basically another country with its own laws,
tax structure, etc.

Kevin Alderman

Kevin, I should have my EFI working by the time I am out there.
I'll bring it down and we can try it on one of your engines.
What kind of ignition coils have you decided to use?

Paul Lamar


-- The Rotary Engine News Letter. Powered by Linux. ACRE NL web site. http://www.rotaryeng.net You Tube key word PaulLamar2 Copyright 1998-2012 All world wide rights reserved.