Subject: Whitecourt World River Boat Races
From: rotaryeng
Date: 8/16/2012, 9:47 PM
To: AAAA Put this in the To box


  "Any rotaries". In case any of you didn't know, I am the director of a
  non-profit ocean research group, Pelagic-Research.org. We use our boats
  to
  take research groups to catch, tag and study sharks. I am working on the
  design for a boat specifically for our work- It will be approximately 30
  feet long, will have a removable transom and be powered by a pair of
  rotary
  engines shafted to jet drives. We need the jet drives so that the sharks
  and researchers can't be injured by props. We need the transom removed
  so
  that we can pull sharks onto the deck and 3 minutes later send them back
  without lifting or handling them unnecessarily.
  We are collecting funding for the project, and I have a couple of hulls
  picked out that can be modified for our purpose. I will post pics as the
  project takes shape. I am projecting 200 HP per engine, with a pair of
  engines. We are targeting next summer as the splash date.
  For the question of why the rotary- here is the reasoning:
  Jet drives like high speed, and run well in the 4500 to 6000 RPM range.
  The engines have to fit under the deck- the rotaries are small. The
  whole
  package has to be compact, and produce good power with reasonable fuel
  economy. For comparison we used a 250 HP 2 stroke outboard running at
  4500
  RPM which typically burns 14 to 15 GPH. Our goal with this boat is to be
  able to get 30 knots on 15 GPH or less.
  We typically spend a week or more offshore on our trips, and fuel
  stations
  are scarce at best. On top of that, I absolutely refuse to carry
  hundreds
  of gallons of gasoline in our main vessel partly because we sleep on it,
  partly because we don't have gasoline tanks on our all diesel boat. The
  small boat has to be able to carry it's own fuel sufficient for the
  trip. The "mother ship" uses 20 gallons per hour idling and 80 gph under
  way, and takes a crew of 3 just to move it. So, we will tow the smaller
  boat out, use it for the running and shark tendering, and tow it back.
  For those that are counting, that will be 3 engines that I intend to use
  the EFI on. I really don't like carbs on a plane, and I especially don't
  like them under the deck of my boat.
  I am collecting parts for engines in the boat, and any spare parts that
  you
  have would be appreciated. We are a listed non profit in Florida, but
  for
  some reason it seems to be taking the IRS longer to list us as tax
  exempt.
  Go figure.
  Kevin Alderman
  I ran a few numbers to get an idea of the BSFC for the outboards.
  14 GPH is 87.5 pounds per hour at 6.25 pounds per gallon.
  If you divide that by 250 HP you get a BSFC of .35. Too low by a
  factor of .6. Two cycle engines are usually .6 BSFC or higher.
  My guess is you are only using 145 HP while you are getting that fuel
  burn. What do you guess the throttle opening is on the outboard?
  At full power on the outboard at .6 BSFC you would be burning 150 pounds
  per hour or 24 gallons per hour.
  I would nail things down a bit better by connecting a manifold pressure
  gage
  to one of the outboards and record that and the RPM to see the amount
  of HP you are using to go X fast.
  The rotary, at partial power, leaned is .47 BSFC.
  Therefor the rotary at 145 HP will burn 68 to 69 pounds per hour or 11
  GPH.
  At full power (250 HP) and a BSFC of .5 for the rotary 20 GPH.
  At full power (200 HP) and a BSFC of .5 for the rotary 16 GPH.
  Here is a HP and BSFC chart for the Le mans p-port 4 rotor.
  The dotted line is leaned.
  I think Dave Atkins sells a Marine water cooled exhaust manifold.
  Paul Lamar
  As far as BSFC on the outboard, no we were not at WOT. Your guess at 140
  or
   so is probably about right, cruise on plane. I ran the numbers because on
   the way in we ran out of fuel. The owner of the boat said that there was
  no
   way that we were out, but the numbers do not lie, and upon removing the
   sending unit from the top of the tank the bottom of the tank was clearly
   visible. Out of gas.

   We do not plan to run our research boat as a speedboat, but it is nice to
   have power available, however a 4 rotor likely wouldn't fit in the space
  we
   have available below the deck. Its primary use is to patrol a 2 mile
  radius
   around the mother ship looking for and dealing with sharks.Since much of
   our time is spent at lower throttle settings just easing around (2500 rpm
   or so) I will likely go with a Renesis and leave it with standard ports
  and
   NA.

   The water cooled exhaust is always welcome :)

   Kevin Alderman

   I am not advocating a 4 rotor. I just used that to illustrate what BSFC
  you are
   likely to get. It applies to all rotaries. 1,2,3 or 4 rotors. The RX8
  engine is no
   better at higher power levels. It just scores well at idle and low RPM.

   I thought water cooled exhaust was mandated by the Coast Guard.

   Paul Lamar

  Actually, water cooled exhaust is optional. We can always run a dry stack
  vertically if we want. Matter of fact, the Coast Guard 47' motor lifeboat
  has dry manifolds. Only wrapped with turbo insulation tape. The engines
 are
  Detroit Diesel 6v 92 turbo with v drives.

  Kevin Alderman

  Maybe it is just California lakes.

  Paul Lamar


 Cant speak to California, its basically another country with its own laws,
 tax structure, etc.

 Kevin Alderman

 Kevin, I should have my EFI working by the time I am out there.
 I'll bring it down and we can try it on one of your engines.
 What kind of ignition coils have you decided to use?

 Paul Lamar


 Right now I have and will test the engine with the stock igniter coils. I
finally installed the plate under the engine and have decided to install a
spacer between the factory oil pan and the plate. I know, another place for
an oil leak but I dont have time at the moment to fabricate a new oil pan.
I have 4 factory injectors, but haven't built the intake yet either. I
needed to mount the engine so that I could determine actual cowl clearance.
Tight is an understatement.
I plan to run the engine on a pair of carbs to get some time on the engine
before we get to the end so to speak- I hate surprises.

Paul, if you get a board and make progress, I will buy one from you and
have it connected before you spend time getting all the way down here.
Remember, I live in the Keys, almost to the end of the US on this side. We
are a good 8 hours from the Orlando area, longer from anywhere else except
for Miami- which is around 2 hours away.

I do have an empty apartment under the house though if you make it down
here :)

I have part of the code for the Arduino unit, but it has not been tested at
all at this point. I had intended to buy a PSRU, but I have some people
that owe me lots of $$, and their decision not to pay back what we loaned
to them last year is putting a damper on the budget. I have to find a way
to install the starter, which will only require time to make a bracket.
More time that's all.

Kevin Alderman

I don't mind driving. I actually like it. I plan on taking week ends off anyway.
I like the keys. I'll bring my computer so I can make changes in the program for my
EFI if necessary. If you stick with the stock 2nd gen coils that makes the EFI much
simpler. I'll set the simple system up for them

It is easy to mount the starter with a plate and spacers.
That right front rubber bushing is subject to exhaust heat. They have been known to
melt. :)

Paul Lamar

The Rotary Engine News Letter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
You Tube key word PaulLamar2
Copyright 1998-2012 All world wide rights reserved.