Subject: Recent flight from Everett to Medford / question for Mark mufflers
From: rotaryeng
Date: 8/31/2012, 6:40 AM
To: AAAA Put this in the To box


 Brian,

 You stated "...my EGT temps- they show up to 2000 at times- and above
 1800 most of the time in cruise."  I too experienced very high EGT's
 in excess of 1800* when I was using a muffler that was too
 restrictive.  Also, power was way down, but it was quiet.  ;-)  The
 high temps ended up damaging the o-rings and I had to rebuild the
 engine.  Since replacing the muffler the egt's have dropped down to
 1600 - 1650* range and power is much improved.  I suggest you examine
 and modify or replace your current muffler.

 Mark


The fuel flow seems correct, and coolant temps seem correct for the  speed,
and HP, so mixture is close. The EGTs are way too high, probably back
pressure and perhaps too large a header diameter. And the probes are a bit close
 in. About 3 inches is the compromise between accurate reporting and long
life.  Each header pipe should be exactly the same length to the collector.
Put a shop  vac hose down each pipe as you build up the system and mark the
length with  tape. Make the second pipe the same length. Shallow angle into
the collector.  Collector about 4 diameters long. Long collector broader HP
range. Short  collector higher peak HP but very short range. Header tube ID
to match the  exhaust liner ID as close as possible. You want high velocity
right into the  collector. Header length in any multipal of 11" to 12" to the
collector. If  the muffler is close to the collector that is the end of
tuning. And best to  have a see through muffler.

The other problem is the 13BREW irons are from a twin turbo engine
and have huge port runners. You want the highest possible velocity at the
port face on the iron. That requires small runners in the manifold and
irons.  Some builders do use turbo irons for NA road race engines, but those guys
shift  well above 10,000 RPM. That is because of the big runners that still
flow well  at those RPM. Those engines have no bottom end power and not
much mid range.

Dave Lemon blends 2 of the 3 runners and ports in a 6 port iron to make
his E production engines. This is the same idea as the turbo irons but  with
more material to play with. He shifts above 10,000 RPM with a really big
street port.

Read this: _http://mototuneusa.com/thanx.htm_
(http://mototuneusa.com/thanx.htm)  Look  at "High velocity porting"

So the selection of turbo irons for an NA engine is an error in my opinion.
 Daryl Drummond uses the stock intake manifold gasket on 250 HP 12A GT-3
engines.  So the runners are amazingly small. (High velocity)

The Pport gets back runner velocity with very early opening of the intake
port. Lots of overlap and late closing of the intake port.

The bridge port opens even earlier than a Pport, plus you control where it
closes by moving the closing line at the top of the port. I think you are
stuck  so long as the turbo irons are installed, unless you add a turbo,
which ends  most of the muffling problems.

Rather than bridge port the irons, I would swap them for non turbo irons or
 add the turbo. Get on the "Nopistons" list and look at the swap and sale
items.

Lynn E. Hanover

 The best muffler for a rotary is 3 to 8 feet long about 4 to 5
inches in diameter.  That gives the lowest aero drag for a given
silencing.  Lowest frontal area.  Mufflers work by the exhaust
gases rubbing on the metal surface losing kinetic energy to skin
friction and losing heat to the metal surfaces.  The cooler the
gases in a pipe the lower the gas speed.  When high speed gas
exits a pipe there is a sudden expansion that causes the noise.

The idea here is to cool the gases before they get to the end of
the inner pipe.  The inner tube is best done in .045 Inconnel
but there is a trade off with thickness.  If you make the inner
tube 2 inches in diameter and use 321 SS make it .065 thick with
a bunch of holes drilled in it.  The outer tube can be .030"
thick 321 SS as it will always run cooler.  Also make the front
of the muffler look like this.  Don't drill any holes for the
first 8 to 10 inches.  The slip stream will blow cooling air
down between the coaxial tubes.  At the back end make the inner
tube 6 inches shorter than the outer tube.  That will act as an
ejector to draw cooling air between the two tubes.  Patent
applied for:)

 A 2 inch diameter SS tube .065 thick 72 inches long will weigh about 8.8
 pounds.

 A 4 inch diameter SS tube .030 thick 72 inches long will weigh about 7.50
 pounds.

 Here is a dwg.

 A 2.5 inch inner tube and a 5 and 1/2 inch outer tube may give a little
 less back
 pressure for a weight trade off.

 Paul Lamar

   Mark ,
   From what you say and from the performance of my plane, I'm
 starting to think that the Hushpower muffler is causing too much
 back pressure and that would explain the anemic performance and
 high EGTs. What type of o-rings were you using and do you think
 that the high EGTs caused O-ring failure and how so?

   Right now I'm thinking of how I can replace the Hushpower with
 the design that Paul just put forth. Its a bit tricky hanging
 that stuff on an RV-4 and working it around the heat exchanger
 and scoop.


   Brian Trubee

 It might be melting inside.

 Here is what Mike Wills did on the RV4 although the front of the muffler
 outer tube
 is not open for cooling air. This is what gave me the idea for the coaxial
 muffler in
 the first place.

 The subtle point is; cooling the inner tube saves weight as there is a
 high temp
 metal durability trade off with weight.

 For an example Perry Mick has been running an early cast iron thermal
 reactor for
 years. They are very durable but they are heavy.

 For anther example Ed Anderson runs SS pipe hand rail with an .109" thick
   wall and
 it hardly discolors. However you don't need a motor mount as the engine
 can be
 cantilevered off the fuse with the exhaust tubes :)

 Paul Lamar

 Brian,

 I was running TES o-rings inner and outer.  The high EGT's exceeded the
 temp limit of the o-ring, allowing it to ooze out between the mating
 surfaces.  I switched to the SS handrail exhaust with a DNA muffler (no
 longer available) and haven't had any more problems, although the DNA
 muffler is not much of a muffler (pretty loud).  People comment they can
 hear me before they can see me.  I wear a Lightspeed Zulu headset.

 Mark

 Got an pictures of those O-rings? Are you sure about the section size?
 Heated silicone can crack cast iron if there is not enough room to expand.

 http://www.rbwagner.com/pages/Rbwagner.html

 Paul Lamar

 Mark,

 What kind of muffler were you using that caused all the back pressure?

 Brian Trubee

 Oh, and also, when you changed the muffler, what kind of performance gains
 did you get?

 Brian Trubee



 Brian,

I saw a big improvement, especially at WOT.  Climb rate improved, top speed
improved, and EGT's dropped significantly.

Paul,

Attached is a picture of the exhaust I'm running now, except for the
downpipe section has been replaced with a DNA muffler.  Sorry, its the best
picture I could find of the exhaust.  I heard they quit making the DNA
muffler.

Mark

I see very little advantage. It looks trick and different and that some times sells :)

For the new guys this is Mark's old engine non p-ported.

As Lynn says you need a "see through muffler". :)

Paul Lamar
-- The Rotary Engine News Letter. Powered by Linux. ACRE NL web site. http://www.rotaryeng.net You Tube key word PaulLamar2 Copyright 1998-2012 All world wide rights reserved.