Subject: Hushpower autopsy-Mazda rotary mufflers
From: ACRE
Date: 9/10/2012, 7:22 AM
To: AAAA Put this in the To box


We'll I finally got some time off to check out my airplane
   after the
round trip from Everett to Medford. The heat cooked my left brake
line, and I suspected the muffler had too much back pressure, so I
resolved to investigate. Here's what I found when I removed my
Hushpower from the airplane. There is way too much heat coming
   off my
muffler- the powder coating on my engine mount is cooked near the
exhaust pipes, even though I coverd them with fiberfrax and
   placed a
SS heat sheild to cover the tubes from view of the exhaust. The
muffler was making like a baby rattle so I cut it open and this
   stuff
came out of the inlet side. I'll send more pictures of the innards.

What I have is an RV-4 with the radiators and oil cooler hung
underneath the plane in a scoop that is reminiscent of a P-51.
   I had
the muffler submerged under the fuselage. I"m thinking that it
   would
be better to have the exhaust pipes exit the side of the cowl, in a
reverse scoop that would vent a huge amount of heat from the
   cowl. The
muffler would be a straight 6 foot muffler like the one Paul
   outlined
about a week ago. It would be mounted along the side of the
   fuselage.
I hate to ruin the clean lines of an RV-4, but nothing would
   ruin it
more than having a mechanical failure due to excessive exhaust heat
bringing the plane down. My biggest worry about this rotary
   conversion
is excessive exhaust heat and how to manage it effectively.

Here is the muffler cut open. The red chunks are what is left
   of the
melted insulation material between the perforated inner case and
outer. The outer case showed signs of bulging. The perforated inner
case was split on the seam closest to the camera. The inner cone
material which is also perforated was mostly gone, but big
   chunks were
still left inside the muffler and undoubtedly were causing some
obstruction.

Here's the split in the inner perforated case. Not real confidence
inspiring.


Crap that I shook out of my baby rattle/Hushpower muffler.


Brian Trubee

That will work out OK but I would put it on the bottom like
   Mike did.
I think you could get the rad under the engine.

Either that or use a narrower rad and put it next to the rad
   under the
fuse.

Paul Lamar


If you ever replaced mufflers on a 2nd or 3 gen RX7 you would know
that Mazda built heavy, massive mufflers. I have a couple
   around here.
Wonder what the inside design is like? Maybe I should cut one open.
Marc Wiese

That would be interesting. Measure the sheet metal thickness.

Paul Lamar




maybe something like this coating both inside and outside of
   the exhaust
system would be useful to reduce heat.
   http://www.jet-hot.com/____coatings/jet-hot-extreme-2500/
   <http://www.jet-hot.com/__coatings/jet-hot-extreme-2500/>

   <http://www.jet-hot.com/__coatings/jet-hot-extreme-2500/
   <http://www.jet-hot.com/coatings/jet-hot-extreme-2500/>__>

chris smale

   Paul and Brian,
   It is great watching your "Big Pictures Minds" working together.
   Listening to ideas on turbo compounding, peripheral ports, etc.
From my perspective of working on GE, Allison/Rolls Royce,
   and P&W
   turbines for 35 years here are a few ideas to add to the mix.
   I am suggesting using a 8" by 12" muffler called a turbo.
   Ideally for power to weight a turbine engine would be best for the
   hobbyist.
   The hardest part would be making the gear reduction, fuel control,
   governor and burner can.
   A turbo actually turns a normal engine (recip or rotary) into a
   turbine
   engine (An old perspective from Hugh MacInnes).
   We then have a compressor and turbine section with the exiting
   engine
   becoming the gear reduction, burner can, Fuel Control and Governor.
   ..... *and with your peripheral port it actually becomes a power
   recovery compound turbo by blowing directly on the rotor!*
   The exhaust is quieted by removing energy and heat.
   The real problem is controlling heat. We would need to use surplus
   compressed air to cool the exhaust. One place air could be
   injected at
   the exhaust sleeve.
   We would use a balanced system that could operate
   'theoretically" with
   no wastegate like the original GM Corvair. (using a extra large
   exhaust
   housing AR of about 1.34 or larger).
   Your thoughts,
   Barry


   Barry,

   Before we go too much further, we need a PSRU that can handle 500+hp.
 We've already had flywheels [flex plate] disintegrate and my
   input shaft broke the
   lock pin.  I would consider installing a turbo, but in my opinion, the
   psru is the weakest link.

   Mark
   P-port 20b


My last trip to Tracy's we discussed this. His recommendation  is to use
an aftermarket aluminum flywheel and attach the PSRU input to that. His
latest iteration of the PSRU will attach to this flywheel easily he says.

As far as the lock pin, that would take more thought. Drilling it out
and installing a larger diameter pin will increase the shear of the pin
itself but at a cost to the strength of the shaft itself.

Kevin Alderman

Just install two lock pins 90 degrees to each other.

We did that on Dave's turbo Reno racer.

When I get home I will send a dwg. We have been around and around on this. I am surprised Tracy did not mention it or start doing it.

Paul Lamar

The Rotary Engine News Letter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
You Tube key word PaulLamar2
Copyright 1998-2012 All world wide rights reserved.