Subject: sealing fiberglass fuel tanks
From: rotaryeng
Date: 9/20/2012, 11:17 AM
To: AAAA Put this in the To box

  I am off the tax thing for a bit- I get too wound up thinking about it.
 So,
  back to my therapy- my Wheeler.

  I bought the kit with the wings closed up but far from complete. I have
  been working on the wings, and yesterday set the wing up in the 5 degree
  position it will be in while on the plane.
  I filled the tanks with water (yes water) to see if they would leak. They
  did in a couple of places. It took about15 hours to leak out 40 gallons. 3
  gallons per hour is a lot.

  The water came from the ribs at the ends of the tanks, where the ribs are
  joined to the top and bottom skins. It leaked around the ribs.

  Have any of you had experience with the epoxies and do they work? I will
 no
  doubt have to open up access holes in the top of the wings, but I want to
  know what the fix is before I get started.

  I can build a jig that will let me rotate the wings so if I get the epoxy
  inside I should be able to rotate the wings for the 40 minute cure time
 and
  coat the inside of the wings. This would have the added benefit of another
  layer of protection from ethanol if for some reason the fuel gets
  contaminated with ethanol laced mo-gas.

  FYI I used water because I feared that this would happen. I can evaporate
  the water easy enough, but fuel residue is hard to remove, and I would
 have
  hated to have had multiple leaks at 4.00 a gallon. I didnt want to use
  pressure because it might damage the wing, and vacuum wouldnt tell me
 where
  the leaks are. As a former utility contractor, I can tell you that a bit
 of
  food coloring in water will tell you where a leak is soon enough. For big
  pipes, Tidy Bowl blue works wonders.  I have spent 1/4 of my time since I
  got the plane re-working what was done before I got it. While the closed
 up
  wing saved some time, I would have preferred to have closed them myself.

  Anyway, if any of you have experience with the sealers, I am all ears.

  Kevin Alderman

 Hi Kevin I'm no expert as i am working under the guidance of experienced
 builders at my build centre and i closed out my wings less than 2 weeks
 back but from what I remember them saying, if there are leaks (we haven't
 pressure tested my wings yet) what you can do is close up the tank and put
 a vacuum to it at the cap. Then mix up resin and aerosil

 Then you go around listening to wherever you hear the air being sucked in
 to the tank and smear your resin and aerosil mix and let it be sucked in
 partially then reduce the suction. Repeat as necessary once dry. Speaking
 of dry, you must make sure all water is evaporated from your water testing
 or it will screw up your tank patches.

 If you want ethanol resistance then you can use Ashland Hebron 998 resin
 and mix that with the Aerosil, or use regular Ashland Herron 992 resin if
 you not planning to make the whole thing ethanol resistant. These resins
 are vinylester, you must check compatibility with what ever you are using
 on your plane.

  If you are planning fully ethanol resistant tanks you will need to at
 least 3 coats of 998 everywhere throughout the entire tank, and I think the
 biggest issue will be sanding down your tanks insides for a good bond if
 you retroactively go through your wing top skins,

 Good luck

 Alex Molteno


I picked up a product from Sherwin Williams this morning- Macropoxy 626. We
used it extensively in sewer treatment plants to coat the interior of
fiberglass, steel, and concrete storage tanks for chemical resistance.
These plants store chlorine, sulfur dioxide, h2so4, and other chemicals for
the process. The epoxy is 76% percent solids, has a solvent base, and is
resistant to almost everything once its cured. I went with a solvent base
product because it will etch into the base. I have to cut 4 x 6 openings in
the wing in each bay to get inside. Once inside I will sand as much as I
can reach, wash with acetone, and then apply the epoxy in 2 coats. This
should take care of the issues I am having. Before I seal the top of the
tank back, I will set the top of the wing level and fill 'er up again. I
think this should do it. I do know that to repair a tank after coating the
easiest way to get it off is with a sandblaster.

FYI, a 1:1 kit makes 2 gallons. One kit along with one gallon of reducer is
$190.00. This product can be thinned and sloshed, but since I didn't close
the wings myself I would feel much better getting a peek inside myself.
Removing (4) 4 x 6 pieces of the top of the wings and patching them back is
not that much trouble and will make me feel much better. And, IMHO,
composite wings should have been epoxy coated to begin with. Lancair
includes the epoxy coating in its kits from the factory and recommends the
builder doesn't skip this step.


I will let you know how it goes.

KA
Kevin Alderman


-- The Rotary Engine News Letter. Powered by Linux. ACRE NL web site. http://www.rotaryeng.net You Tube key word PaulLamar2 Copyright 1998-2012 All world wide rights reserved.