Subject: new 20 B LIM may work for us?
From: rotaryeng
Date: 9/21/2012, 12:16 AM
To: AAAA Put this in the To box



Xcessive Manufacturing 20B Lower Intake Manifold (LIM)

http://www.xcessivemanufacturing.com/ONLINESTORE.html?cid=9&step=2

Just thought I'd share what Xcessive has been working on as of late.

Full length version:


Xcessive's all new cast lower intake manifold for the 20B is based on the
same concept as our original 13B-REW manifold, better runner flow balance,
more volume and more fuel. We've made these manifolds with 6 injector bosses
machined to fit Bosch type top feed injectors with 14mm o-rings without any
adapters. We've placed all the injectors on the inside of the manifold to
keep them away from heat leaving more room on the outside for turbo motors
as well as a cleaner install.



The new lower manifold fits stock upper castings and comes in both a full
height (stock) and short versions. This is the FULL HEIGHT (stock) version.
They are also available with and without fuel rails. This manifold kit
includes the fuel rail assembly. The fuel rail has 3/8" NPT ports on both
ends with a -8 (1/2", 13mm) through hole and comes with the apropriate stand
off's for full height top feed injectors. No more welding bosses onto a
stock manifold and chopping and welding the upper flange, we've done it all
for you in a single brand new piece that'll also out flow a stock manifold.

This Kit Includes

New cast manifold - Full height (stock) version

6 port fuel rail for top feed injectors

Rail stand off brackets and bolting hardware

Front mounting bolt (New boss height)

There is also a short version for easier swapping into non JC cosmo chassis'

Short version:

Quote from Xcessive's website:

Xcessive's all new cast lower intake manifold for the 20B is based on the
same concept as our original 13B-REW manifold, better runner flow balance,
more volume and more fuel. We've made these manifolds with 6 injector bosses
machined to fit Bosch type top feed injectors with 14mm o-rings without any
adapters. We've placed all the injectors on the inside of the manifold to
keep them away from heat leaving more room on the outside for turbo motors
as well as a cleaner install.

The new lower manifold fits stock upper castings and comes in both a full
height (stock) and short versions. This is the short version that is 1 1/2"
(38mm) shorter than stock. They are also available with and without fuel
rails. This manifold kit includes the fuel rail assembly. The fuel rail has
3/8" NPT ports on both ends with a -8 (1/2", 13mm) through hole and comes
with the apropriate stand off's for full height top feed injectors. No more
welding bosses onto a stock manifold and chopping and welding the upper
flange, we've done it all for you in a single brand new piece that'll also
out flow a stock manifold.

This Kit Includes

New cast manifold - Shortened version

6 port fuel rail for top feed injectors

Rail stand off brackets and bolting hardware

Front mounting bolt (New boss height)

If they can make stuff like this for the 20B RX7 conversion crowd, why can't
they make an intake set up for us for BOTH the 13B and 20B?

Marc

All, this is my third attempt to reply as photos make the mail too big, so
you will have to contend with just the one photo.  For parts see
www.billetinc.com.au  This bloke will make anything from alloy, from
complete rotary alloy motors to all parts, cheaper than the current spare
parts from Mazda.  He even makes a dry sump for those who like to fly upside
down.  1 to 4 rotors, take your pick.   Note the modified cooling area
around the plugs in the rotor housing example.

Neil Unger.

Send the big pictures one at a time Neal. One per email message. I have
Linux software that can reduce the file size but not change the apparent quality
of the picture.

What is the wear surface in this rotor housing? That is the million dollar
question.

Paul Lamar

Paul,
         Just spoke to Darren, from Billetinc. and he tells me that you can
have any option you nominate in the rotor housings for wear surface, but he
normally does spray silicone carbide.  That tell me nothing, but may
enlighten the more knowledgeable.
Neil.

We have some people at a company here in SoCal that did a lot of experimenting with
this. The only thing that really works, other than the hardened steel insert that
Mazda uses, is detonation gun coating. The silicon carbide particles are shot from a
gun and mechanically embed themselves into the aluminum. This is the process Mazda
used on the Le Mans winning 4 rotor. It is then necessary to diamond grind the
coating. The whole process is rather expensive.

Mazda says:
"Investigation of material compositions and heat treatments  led to
adopting, as the base metal of the  rotor housing, a T6 heat treated
aluminum alloy AC4D (5i 5.0%, Cu 1.2%, Mg 0.5%).  The trochoid surface on
which the apex seal slides is given hard chrome plating to provide good
wear resistance. To prevent the chrome plating from fatiguing and peeling
off under the apex seal's vibrating load, study was made on how to
provide a better trochoid surface for chrome plating adhesion. As a
result a new process called SIP (Sheetmetal Insert Process) was developed.
As shown in Fig. 3, the aluminum rotor housing is die-cast under high
pressure to the trochode-shaped sheet metal with one side jagged in the
saw-tooth manner for better bonding with the aluminum alloy. The SIP rotor
housing offers a markedly improved surface insuring proper adhesion of
chrome plating.  The effect this development was evaluated using a
contact rolling fatigue tester in which a loaded test piece is rolled
as shown in Fig. 4.  Fig.5 indicates that SIP offers ample adhesion
to the chrome plating.

CHROME PLATING - Rubbing by the apex seal used to cause the
trochoid surface to develop the so-called chatter mark - ripple marks
and scuffing.

To overcome this problem, study was made on material of the apex seal and
chrome plating of the trochoid surface.

The electroplating procedures studied for surface-treating the trochoid
surface included nickel plating containing silicon carbide, cermet spray,
and chrome plating, and this last was adopted for quality and productivity.
The chrome plating has a Vickers hardness of more than 1100. Furthermore,
the chrome plating, which is characteristically poor in wettability with
oil, is provided on its surface with minute pores. and channels for
effective oil retention,

As shown in Fig. 6, the chrome-plated surface is given electro etching and
honing to make it pinpoint-porous, followed by another electro etching
which produces micro-channels. This micro-channel porous (MCP) plating
is effective in maintaining oil film and reducing the friction with the apex
seal."
End of Mazda quote.

Paul Lamar

-- The Rotary Engine News Letter. Powered by Linux. ACRE NL web site. http://www.rotaryeng.net You Tube key word PaulLamar2 Copyright 1998-2012 All world wide rights reserved.