New Subject, Does anyone have a dimension-ed drawing for a 3:1 reduction box
modeled on Tracy's Box?
Milo
This is what I have so far.
Paul Lamar
I measured mine up for CAD drawings before I assembled it, but with the
holidays I haven't had time to draw it. I will get to it shortly.
Kevin Alderman
Kevin, would appreciate a copy. I think it is time to do a 3:1 drive. Would
like suggestions from one and all on the appropriate gears by part number if
possible. Also design concepts as well, like integration with the standard
bell housings to keep the costs down.
milo
If you build it like this you can use a relatively cheap constant speed
hydraulic prop.
I forget the attachments.
Paul Lamar
I do that also. I thought they were grey hairs overcoming me, but there is
some evidence they may be blonde:-))).
Dale Davies
Paul, Jean Prudhomme has a PSRU similar to your attachment drawn up in Rhino
and made the casting patterns for it. I don't know the current status but
perhaps he will let us know.
george grimes
George, do you know what the part numbers for the bearings and the material
and heat treat for the shaft
Milo
If you copy the Lycoming crank shaft dims you can use the Lycoming shell bearing
and front stretch over oil seal.
That is what I would do. It is a proven design. Some times you can make the
smallest of changes in a design and run into all sorts of unforeseen problems.
Paul Lamar
Paul,
The real expensive element is the steel shaft, did you price
out a forging blank for the 3:1 setup?.
I have an idea for segmenting that shaft so that it could be
machined out of 4140 stock, but first we have to deal with the bending loads.
Milo
Contact a Lycomming overhaul shop and buy a cracked crank.
They generally crack is the journal fillets.
Cut at the first cheek and tig weld on a flange for the planet carrier.
All the Ross boxes were tig welded flanges for the planet carriers.
That is a low stress area of the crank for our application.
Not a low stress area for a piston engine.
Just 600 foot pounds of torque. No bending.
No prop gyro bending loads that affect the prop flange end.
Or you can do something like this bunch of screws bolt on flanges.
Paul Lamar
THANKS! Paul, that helps quite a bit.
Does anyone have an appropriate sized Lyc. shell bearing good for
230hp kicking around the shop that they can spare?
milo
Milo, As far as I remember Jean got a price of around $300 for a piece of
4140 billet. He was going to rough out the machining to some point on the
CNC G-code, skip down to the next area and rough out etc. then delete the
code that went between. The idea is to reduce the CNC machining time.
The bearings are larger diameter than Lycoming as shown on his drawing. I
recall 3.25 diameter and from a big block automotive engine from Chrysler or
GM. Several main bearing shells, one of which was the thrust bearing. Oil
drain back between the shell locations and one of them isolated the constant
speed prop oil which could be at a pressure different than the engine oil
pressure. I remember Jean had some castings poured and you might get the
guinni pig discount on a pair of unmachined castings I have also designed a
PSRU but heavier than the one Jean has. Same diameter shaft but sperical
roller bearing at the prop flange and timken bearings at the rear of the
shaft and input shaft.There is also one journal bearing that floats on the
prop shaft which is restrained from rotation by the feed tube that passes
through to the outside of the housing. My patterns are about 90% done and
the bearings are in storage. These patterns as with the engine patterns
need a little detail sanding and surface sealing. I use a borg warner 4407
planetary from the transfer case of the F-350 truck with a ratio of 2.64:1
which has a torque capacity three times as high as the F4OD planetary which
is 2.85:1 I would not recommend my PSRU to anyone else. It is a one-off for
a turbocharged 4-rotor designed for HP capacity rather than minimum
weight.The roller bearings added 8 pounds of weight, required a larger
diameter casting for another 6 pounds, An integral bell housing/oil tank
which added length (and eliminated the prop shaft spacer) and added
considerable weight compared to Tracy's spacers.
The other planet set in that transmission is I believe 3.17 :1 but I
would have to verify the ratio These ratios are all with the ring gear fixed
and drive through the planetary carrier. The rotation is the same direction
as the input shaft. When driving from the ring gear there is less reduction
and and the rotation direction is opposite the input shaft.
Jean and I sketched up a prop flange attachment that allowed use of a
standard oil seal slid on the front of the prop shaft. The prop flange with
integral hub slid on the front of the shaft. Then there is a .060 deep
depression in the shaft with split locks similar to what is used on
automotive valve springs. The tapered bore flange around the split locks
has a bolt pattern matching the prop bolts and mounts the hollow dowels for
the prop.The prop bolts go through both flanges with nuts behind the tapere
bore flange.. Jean opted for a large fillet radius on the prop flange and
the stretch over the thrust land oil seal. I went with the large radius one
piece shaft and the standard triple lip seal on the shaft followed by all
the bearings which get progressively smaller bore back to a fine thread
retaining nut.
The starting point is the diameter of the prop shaft at the prop end sized
for the gyroscopic loads. Then select bearings rated for the speed the
shaft turns. At these diameters speed rating drives bearing selection more
than load capacity.. Draw the shaft, bearings, and planetary and fit the
inside of the case around the parts remembering that you need 2 degrees of
draft on the rough casting to get the pattern out of the sand. Draw the
outside of the casting around everything keeping the 2 degree draft in mind
and generally it is 2 degrees in the opposite direction. Since there are
usually gussets around the outside, thinning down the rough casting on the
inside while in the lathe boring the bearing seats works to get rid of extra
thickness needed to cast the parts.. Some form of end cover to close off
the gearbox and mount the input shaft will be a second part. If you draw
this shaft and it's bearings along with the prop shaft it will aid in
conflict between the two housing parts..
Unless you require a constant speed prop or a different HP rating I really
don't see a reason to design and test a PSRU as long as Tracy's box is
available.
george grimes
George,
The sketch you showed me of Jeans shaft illustrated thrust rings in two
locations, I believe. If that is the case
what thrust shell bearing did he intend on using?
Does Lycoming use thrust shell bearing on their shafts? If that is not
the case how does Lycoming control the
thrust? milo
BTW I want to point out one thing about lower cost hydraulic constant
speed metal
props.
Not only are they $4000 cheaper than the European composite wood constant speed
electric props they are considerably more efficient as the tips are thinner.
Tracy Saylor owner, of the fastest RV6 in the world at 238 MPH (beefed up tail),
tested a metal constant speed compared to a European wood constant speed and
the metal was ten MPH faster.
Paul Lamar
milo, I haven't posted any sketches of Jeans designs. Possibly it was posted
from something Paul had. Jean was useing the #5 main bearings from the
automotive engine. I think the use of two had to do with a redundant
bearing with a much narrower journal in case the primary bearing had a
problem. The extra clearance allowed ckecking the clearance of the thrust
bearing during preflight and prevent binding of the two thrust bearings due
to thermal expansion. There is also something to do with a slot across the
thrust bearing face to spread oil as it turns.
george
Just remember vibration problems could be more severe with metal props than
with wood or composite props. [Idea: metal prop with core consisting of
damping material…]
Gene Kahn
Vibration???? We don't have any stinking vibration on the rotary :)
Paul Lamar
The Rotary Engine News Letter. Powered by Linux.
ACRE NL web site.
http://www.rotaryeng.net
You Tube key word PaulLamar2 Copyright 1998-2013
All world wide rights reserved.