Subject: Penetrating Oil-equivalency, vs home made
From: rotaryeng
Date: 1/7/2013, 8:21 AM
To: AAAA-rotaryeng



"Machinist's Workshop" recently published information on various
penetrating
oils. The magazine reports they tested these products for "break out
torque" on rusted nuts and bolts. A subjective test was made of popular
penetrating oils, with the unit of measurement being the torque
required to
remove the nut from a "scientifically rusted" bolt.

Average torque load to loosen nut:

No Oil used .........................516 foot pounds

WD-40 ...............................238 foot pounds

PB Blaster ..........................214 foot pounds

Liquid Wrench .......................127 foot pounds

Kano Kroil ..........................106 foot pounds

*ATF/Acetone mix .....................53 foot pounds*

*The ATF/Acetone mix is a "home brew" mix of 50/50 automatic
transmission fluid and acetone.

Note this "home brew" released bolts better than any commercial
product in
this one particular test. Our local machinist group mixed up a
batch, and we all now use it with equally good results. Note also
that Liquid Wrench is almost as good as Kroil for about 20% of the
price.

ATF/Acetone mix is best, but you can also use ATF and lacquer thinner
in a
50/50 mix.

ATF = Automatic Transmission Fluid

Please tell us which ATF was used. There are various specifications.
Has anyone tried this as a tapping compound or a cutting oil?

Al Rees
I do not think which ATF you use would make much difference for this. The
different fluids have more to do with the clutch materials to provide the
desired application qualities. We used to put 1 quart of the Type F in the
TH350 transmissions to help them "grab" a bit quicker. It firmed up the shift
a little. If you changed to all "F" you would fry the trans due to the clutch
grabbing before the other had released. GM transmissions had a smooth shift
but that slip during engagement and release allowed a lot of wear. The
Chrysler Torqueflight transmissions engaged the clutches quickly which gave a
rougher shift but the trans did not wear as much.

Dale Davies

That is really interesting Dale. Thanks for that clarification. I was driving
my Honda Odyssey to the east coast from Ca and I had the synthetic oil changed
at Walmart before I left.

The minimum wage employee left the auto tranny dip stick lose and the trannny
blew all the fluid out while climbing 30 mile long hill in the desert.
Just as I was getting to a gas station on the top of the hill the RPM went
to 6000 and the Honda would barely move. Copious amount of smoke was coming
out. They had only one kind of auto tranny fluid and no way to get it
in the 3/8 hole. No funnel small enough to fit. I rolled up paper and used
scotch tape to hold it together. Took a long time to fill it up.
To my amazement it worked and the tranny starting working again.

But it definitely shifted with more jerk. The Honda made it to the east
coast and back and is still working for two months after so far.

Paul Lamar

 When in a pinch you can use a trick that we used years ago when we had a
sail boat in the British Virgin Isles.  Occasionally we had to do some work
on our Aux Diesel engine which would require the "unfreezing" of salt water
corroded nuts and bolts (ie alternator tensioner arms and the like) To keep
the insects away we used a product called Skin-so -soft (I think AVON) All
of the sailors used it and it was the prevalent smell in that part of the
world.  It just so happens that that material was an excellent penetrating
oil.  I used it many times.-- and it kept the bugs away


Rich


The Rotary Engine News Letter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
You Tube key word PaulLamar2
Copyright 1998-2013 All world wide rights reserved.