Subject: Penetrating Oil-equivalency, vs home made
From: rotaryeng
Date: 1/7/2013, 10:14 PM
To: AAAA-rotaryeng


Subject: Penetrating Oil
  "Machinist's Workshop" recently published information on various
penetrating
oils.  The magazine reports they tested these products for "break out
torque" on rusted nuts and bolts.  A subjective test was made of popular
penetrating oils, with the unit of measurement being the torque
required to
remove the nut from a "scientifically rusted" bolt.
  Average torque load to loosen nut:
  No Oil used .........................516 foot pounds
  WD-40 ...............................238 foot pounds
  PB Blaster ..........................214 foot pounds
  Liquid Wrench .......................127 foot pounds
  Kano Kroil ..........................106 foot pounds
  *ATF/Acetone mix .....................53 foot pounds*
  *The ATF/Acetone mix is a "home brew" mix of 50/50 automatic
transmission fluid and acetone.
  Note this "home brew" released bolts better than any commercial
product in
this one particular test.  Our local machinist group mixed up a
batch,  and  we all now use it with equally good results.  Note
  also  that Liquid  Wrench  is almost as good as Kroil for about 20%
  of the  price.
  ATF/Acetone mix is best, but you can also use ATF and lacquer thinner
in a
50/50 mix.
  ATF = Automatic Transmission Fluid
  Please tell us which ATF was used. There are various
  specifications.  Has anyone tried this as a tapping compound or a
  cutting oil?
  Al Rees


I do not think which ATF you use would make much difference for
  this. The  different fluids have more to do with the clutch
  materials to provide the  desired application qualities. We used to
  put 1 quart of the Type F in the  TH350 transmissions to help them
  "grab" a bit quicker. It firmed up the shift  a little. If you
  changed to all "F" you would fry the trans due to the clutch
grabbing before the other had released. GM transmissions had a
  smooth shift  but that slip during engagement and release allowed a
  lot of wear. The  Chrysler Torqueflight transmissions engaged the
  clutches quickly which gave a  rougher shift but the trans did not
  wear as much.
  Dale Davies


  That is really interesting Dale. Thanks for that clarification. I
  was driving my Honda Odyssey to the east coast from Ca and I had the
  synthetic oil changed at Walmart before I left.

  The minimum wage employee left the auto tranny dip stick lose and
  the trannny blew all the fluid out while climbing 30 mile long hill
  in the desert. Just as I was getting to a gas station on the top of
  the hill the RPM went to 6000 and  the Honda would barely move.
  Copious amount of smoke was coming out. They had only one kind of
  auto tranny fluid and no way to get it in the 3/8 hole. No funnel
  small enough to fit. I rolled up paper and used scotch tape to hold
  it together. Took a long time to fill it up. To my amazement it
  worked and the tranny starting working again.

  But it definitely shifted with more jerk. The Honda made it to the east
  coast and back and is still working for two months after so far.

  Paul Lamar


I owned a '91 Honda that shifted hard. Best tranny guy around sold me a
bottle of "LubeGuard", about $8 and it fixed everything.  Car was still
running at about 300K miles, last I heard. Guy claimed that the secret
ingredient was jojoba-bean-oil.  Comes from some plant that grows in the
deserts of the SW US

RBerglund

The Rotary Engine News Letter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
You Tube key word PaulLamar2
Copyright 1998-2013 All world wide rights reserved.