I had to go to the SF valley to check out a laser jet tube cutter
and MM welder and stopped off at a Pick a Part junkyard.
I found this GM LS1 mass airflow sensor for $45.
Retails for $399.95.
Took me five minutes to get it out of the wrecked Isusu truck.
All it took was 2 screw drivers a phillips and a straight :)
"Mass air induction systems measure airflow with an electronic
"hot-wire"
type mass airflow sensor. The sensing element in the air intake
provides an
output voltage reading that is directly proportional to the amount
of air
that is entering the engine. This airflow measurement reduces the
calculations required to control fuel and ignition spark advance.
Mass airflow sensors can react quickly and accurately to sudden
changes in airflow."
Usually it is 0 to 5 volts. I will use this with the Arduino program
and a slide throttle on the RV4.
They are easy to locate and mount as you put them upstream from
the slide throttle in 2.75 inch ID hose.
Paul Lamar
Hi Paul, The early types had a circuit that at switch off the wire
was heated to burn off any gunge sticking to the wire and cleaned
up the wire for next time engine was started. Hard to see the $400
value in those things.John Burey.
You can buy new ones made from plastic here for $100.
http://secure.ultracart.com/__catalog/PSI/ACCESSORIES/MAF-
<http://secure.ultracart.com/catalog/PSI/ACCESSORIES/MAF->
Sensors/ACC-1004.html
Connectors called pig tails here:
http://secure.ultracart.com/__catalog/PSI/PIGTAIL-__EXTENSIONS/LS-
<http://secure.ultracart.com/catalog/PSI/PIGTAIL-EXTENSIONS/LS->
Vortec-Pigtails/PIG-1019.html
While searching for a schematic for the LS1 MAF I ran across this
explanation
of the advantages of putting the injectors at the upstream end of the
p-port runner tubes.
http://www.hotrod.com/__techarticles/engine/hrdp_9812___10_common_efi_mistakes/__viewall.html
<http://www.hotrod.com/techarticles/engine/hrdp_9812_10_common_efi_mistakes/viewall.html>
"Carbureted and throttle-body fuel systems are considered wet flow.
Port EFI
designs (an individual injector for each cylinder) are referred to
as dry flow. In a wet-flow system, a mixture of air and fuel
coarses through the intake-manifold runners; in port systems, the
fuel is administered at the end of the intake-manifold runner just
prior to entry into the cylinder head. The laws of physics dictate
that for every 10 degrees Fahrenheit of change in the temperature
of the charge, there will be a corresponding effect of 1 percent to
the specific output of the engine-raising the charge air
temperature will decrease power; cooling it will have the oppositeeffect. Wet-flow manifolds enjoy the advantage
of cooler charge airtemperatures created by the vaporization of the fuel. When changingfrom a liquid to a gaseous
state, this transformation will consume
some of the heat from the intake tract. Dry-flow manifolds do not
benefit from the latent heat of vaporization."
"The results of this phenomenon cause fuel-injected engines to be
affected
more by higher ambient temperatures and under hood heat."
"The best-running EFI cars breathe cold air from a ram-air kit."
------------------------------__-----------------
Kevin's Arduino EFI code (attached) does not have a mass air flow
sensor input.
It works like Tracy's code on intake manifold pressure and air
temperature
correction I think. I suspect a mass air flow sensor would simplify
the code some what and most important the look up table.
In any event the 5 wire version of this mass air flow sensor has
a temp sensor for $2 more. A real bargain.
Paul Lamar
What about redundancy with a MAF sensor? Can you run two of them in
a row?
Everett Rankin
I don't see why not.
BTW I think one might be able to do away with the math in the EFI
program speeding it up greatly. Mass airflow changes with temperature
so no need to calculate the mass flow from intake man pressure
and intake air temp.
Paul Lamar
You could Everett, but two things. Each one does restrict airflow a bit. Two
would just be more. Another thing, that honeycomb is for two things. First is
to prevent large objects coming through and damaging the hot wire. The second
is "straightening vanes" to get the air from being turbulent.
Paul,
Previous discussion was that the MAF output was not linear and would cause an
issue to deal with to get the injection pulsewidth corrected?
Dale Davies
It is non linear and that concerned me when using them with a very simple
555 injection system. Now the price of powerful Arduino computers came
down to $20 bucks on Ebay. The non linearity of mass air flow sensors
can easily be handled in a look up table.
Based on my limited knowledge of Arduino programming it does not appear
Kevin is using a look up table. It appears to me he calculates the injector
pulse width based on MAP and intake air temp. This takes time as the Arduino
processor (Atmel ATmega2560) does not having built in hardware floating point
math unlike your PC. It does have lots and lots of I/O however unlike your PC :)
See the attached block diagram. One of these days we will find something
that has it all :)
I have loaded Kevin's code into a doc editor and generated a doc file
so the code does not get macerated each time it goes through the
internet. Spaces and carriage returns are meaningful. To compile
it you must remove it from the doc file as plain text. If you
makes changes rename it and keep it in the doc format.
http://arduino.cc/en/__Reference/HomePage <http://arduino.cc/en/Reference/HomePage>
Paul Lamar
Paul, I am wondering why we are entertaining the idea of look up tables when
using a mass air flow sensor.I did a little research on this in 2010
concerning the 90mm MAF throttle body used on Ford mustangs with the 302 CU
in engine.
The MAF has a built in computer that adjusts the 0 to 5 volt
output compensating for density altitude, air temperature and relative
humidity. This voltage when converted to a digital input will track the
curve of airflow versus voltage by the formula voltage cubed plus a constant.
The constant is the intercept value of voltage for 0 air flow. It is
irrelevant that this is not a linear progression. The goal is a numerical
amount of the mass of air passing the sensor into the engine which then
needs the proper ratio of fuel added to it. That relationship would be
linear such as 14.7 pounds of air needs 1 pound of fuel. Intuition tells me
that the black box the connector to the Gm MAF is attached to does the same
things as the one used by Ford. Just because the Arduno board has thousands
of counters, timers, and a bunch of AtoD converters doesn't mean we have to
use as many as possible.
The more code we implement the more we will push
the RPM limit for sequential injection. Advancing ignition and injector
timing referenced to operating speed seems desirable, and outputting the
PWM count for the injectors, RPM, and ignition timeing to a display or data
logging would seem to be a good use of code if it was done on a separate
processor or read from a cache from the processor. The use of look up
tables would seem to be treating symptoms rather than the disease. It would
be using a value stored in a matrix cell after trying to select the cell
from combination of input sensors. With dynamic resonance of the intake
runners as an example trying to skew the results. The mixture would be
correct some percent of the time but that hardly sounds like a design goal.
george grimes
You might be right. If so all you need is a 555 system. No computer.
http://www.rotaryeng.net/simple-cheap-555.html
Substitute the MAF for the MAP sensor.
I wish I had an infinite amount of time to try all these things.
Paul Lamar
The Rotary Engine News Letter. Powered by Linux.
ACRE NL web site.
http://www.rotaryeng.net
You Tube key word PaulLamar2
Copyright 1998-2013 All world wide rights reserved.