Delete the last program and replace it with
this. Debugged and much improved. The old one won't work
anyway.
I am getting a little practice with 2D arrays in QB64
I have decided to use a 10 by 10 array which is
a little larger than usual for an EFI system.
As I recall Megasquirt uses an 8 by 8.
The array is a look up table. The x axis is the RPM
and the Y axis is the mass airflow.
Arrays have the form of A(xcoord,ycoord) in BASIC.
There will be a xcoord entry about every 75 RPM
and about every 0.5 Volts ycoord from the mass air flow
sensor. About 100 entries total It looks like this.
^ x x x x x x x x x x x x
M x x x x x x x x x x x x
A x x x x x x x x x x x x
F x x x x x x x x x x x x
^ x x x x x x x x x x x x
V x x x x x x x x x x x x
O x x x x x x x x x x x x
L x x x x x x x x x x x x
T x x x x x x x x x x x x
S x x x x x x x x x x x x
...... RPM
x represents a mixture setting or pulse width for the injectors.
I wrote a program to initialize the array to 30
because it is rather tedious to type all that in by
hand. Simple QB64 program. The array will be adjusted
before I run the engine on it. The tuning procedure
is dump the array to a PC and load it into a spreadsheet
program. Edit as needed and ship it back through the
USB to the EFI computer. The next guy that builds
a EFI computer like this will have a head start.
Eventually we will accumulate a bunch of tables that people
can try when they are starting up for the first time.
CLS
OPEN "mix-tab.bas" FOR OUTPUT AS #1
FOR x = 1 TO 10
FOR y = 1 TO 10
y$ = STR$(y)
x$ = STR$(x)
n1 = 30
num$ = STR$(n1)
PRINT #1, "A(";
PRINT #1, x$;
PRINT #1, ",";
PRINT #1, y$;
PRINT #1, ") =";
PRINT #1, num$
NEXT y
NEXT x
CLOSE 1
END
Small sample of the output. 100 of these total.
A( 1, 1) = 30
A( 1, 2) = 30
A( 1, 3) = 30
A( 1, 4) = 30
A( 1, 5) = 30
A( 1, 6) = 30
A( 1, 7) = 30
A( 1, 8) = 30
A( 1, 9) = 30
A( 1, 10) = 30
A( 2, 1) = 30
A( 2, 2) = 30
A( 2, 3) = 30
A( 2, 4) = 30
This gets loaded into the program in the init area.
To read the array.
Inj-width = A(RPM,MAF)
Super simple. Temperature is compensated
automatically by hot wire mass airflow sensor.
Paul Lamar
For all you guys in corporation that filter out zips
send me your home email.
I also forgot to mention our analog tach outputs
RPM as a zero to 5 volt signal so both array index's
are the same.
Paul Lamar
Hey Paul,
Change the file extension from .zip to .piz. The email filters are
usually too stupid to know this is a zip file so it passes them through.
When the intended victim saves the file all he/she has to do is change
the file extension back from .piz to .zip and all is well.
Mark LaPierre
Thanks for tip Mark. Did you try this program in your copy of
QB54. If not please do.
Paul Lamar
The Rotary Engine News Letter. Powered by Linux.
ACRE NL web site.
http://www.rotaryeng.net
You Tube
http://tinyurl.com/beqqxas
Copyright 1998-2013 All world wide rights reserved.