I was using Blendzall's Racing Castor premix in my rotary, guess it was
a bad idea, it seems ALL the apex seals are
stuck solid due to gum/varnish build-up!! NO! HELP! Anyone know of
anything I might be able to squirt inside it to
dissolve that gunk and save me from a pull & rebuild?! THX!
Dan Gorsline
Try ATF for a few days.
If it is a 13B.
Then use a 1/4 inch dowel to work the seals in and out in their slots
through the exhaust ports.
If it is an RX8 you are stuck :)
Once it is running again pour some water in the intake to blow out the
carbon.
Not enough to kill it. Keep it running while doing so.
Use only 2 cycle oil premix in the future.
Paul Lamar
--
Dan, Being a model airplane addict that uses castor oil for lubricant,
have seen this castor varnish many times in my older engines. The only
thing I have ever found to clear this gunk out is more model airplane
fuel. That would be methanol, nitro methane , and castor. 10% nitro should
be sufficient. Fuel with synthetic oil will work better also to clean, and
not rust everything together.
Bob Mears
Hi Regarding 2 cycle premix, some have an additive to ensure cold weather
pumping that gives a low flash point, so be careful on this.
The simple Test, compare a known trouble free oil with this test, base test
and test oil samples side by side.
Put a small level of oil in a steel cap on a cold hot plate, switch on and
keep poking it with a match stick and note the temperature at which it
starts to goes sticky, the better oils will stay fluid to much higher
temperatures, this on the face of it may sound a very simplistic test and it
is, but it used to indicate and mimic our test finding quite well.
Regard
Bob Rowley
ex BSA & Norton UK
--------------------------------------------------------------
-------- Original Message --------
Subject: Oil Bake Off
Date: Mon, 14 Sep 1998 19:03:21 -0700
From: Paul
<rotaryeng@earthlink.net>
To: bit@any
Take One can of Friskies Sliced Chicken In Gravy 13.5 oz size.
Feed cat until can empty.
Wash can and remove label.
Cut down can until 3/4 inch high.
Use one teaspoon of oil of your choice.
Preheat oven for 1/2 hour at 500 degrees F.
Place cut down can with oil in oven and bake at 500 degrees F for one
hour.
Paul
Neil A. Kruiswyk wrote:
I can't believe what I started but it's all good info. I'm out right now
but I'll be getting some Amzoil 10W30 for the crankcase and I'll pick up
some 2 stroke oil and run the test. Thank goodness I have a little toaster
oven that I can take outside!!
How much oil were you testing? How big was the container? (how much in the
cat food can?)
Neil
-------- Original Message --------
Subject: Oil Bake Off
Date: Sun, 13 Sep 1998 00:29:20 -0700
From: Paul
<rotaryeng@earthlink.net>
To: bit@any
Your not going to believe this Tracy.
MMO was the worst of the lot. Nothing but thick varnish was left. No
liquid was left. I also burned a fresh sample and it burned with thick
black smoke which means a lot of particulates.
The best I have tried so far has been the Quaker State Universal 2-Cycle
Engine Oil. Only about 15% of the volume was cooked off. No varnish. The
oil turned black and thickened slightly but that was about it.
I set fire to a fresh sample and it burned a little bit like a sparkler
with very little smoke.
Rank:
2 cycle was first
synthetic was second
10W30 was third
and MMO was last.
Course this is not a definative test. The proof is in
the using. I can't wait to see the inside of your engine.
How about borrowing a bore scope and have a look through the big spark
plug hole. Take your exhaust off and have a look at the center of the
apex seals.
If anybody wants to try this please do.
One teaspoon of oil in the bottom of a cut down cat food
can, baked in a pre-heated oven at 500 degrees F for one hour. Get ready
for a stinking kitchen. I would set up ventilation fans as well.
Paul
The Rotary Engine News Letter. Powered by Linux.
ACRE NL web site.
http://www.rotaryeng.net
You Tube
http://tinyurl.com/beqqxas
Copyright 1998-2013 All world wide rights reserved.