Subject: Cowling and loose parts
From: AAA-rotaryeng
Date: 3/3/2013, 5:13 PM
To: AAA-rotaryeng

Paul,
Some pictures of a tight cowling. No word yet on how well (or not) it will cool. I'm fairly confident about the
water cooling, but the oil cooling intake, I think, is questionable. Will tie the plane down outside and begin
testing in earnest as soon as I can dig it out of the shop.


Replaced a lot of parts (almost all!) during the rebuild. Wondering if any in the group would care for the
leftovers. Chris Cosman lives nearby... Most parts are about 1986 13b, some earlier. The rotor and housings are
nearly perfect for wear. Jeff began machining the peripheral housing for a P port, only to learn that its through
bolt spacing is different, and will not allow for a 2 in intake. It could be made smaller, however. I have all the
3mm seals and springs for the rotor. Look at the pictures, make an offer and get it out of here.


Lewis Bjork

You need to replace that black rubber hose with aluminum tubing or silicon
hose and constant tension hose clamps. I hope there is beedings on the fittings
where the hose is clamped to. The pressure can build to 30 psi or more
in the cooling system and that 50 pound force can jerk the hose off with disastrous over heating. I hate to see you
waste all your time and money for saving a few bucks on the cooling plumbing. Not to mentions getting hurt or worse.


Do you have my cooling book? If not contact me by saying private and I will get you a bargain price.

Paul Lamar

I do need to get over and see your project Lewis.

Chris Cosman

Like this?


Everything is beaded and constant tension clamps.

ran it up to 5000 rpm today. its throwing oil out the breather, I think. too much In The tank. the o ring block
around the P port has begun to leak coolant. the o ring is in place, I think the leak is the flat side against the
housing. I used rtv sealant there. Need to fix it. any recommendations?
also getting bogus indications from my temp and pressure senders for both oil and water. using a MGL engine monitor.
probably have to buy their probes, too.

Lewis.

Much better. Now just make sure you don't have any air bubbles in the rotor housing near the spark plugs up or you
will melt the rotor housing.

When was the decision made to mount the engine unnaturally plugs up? :)
No telling what the oil breather is doing plugs up :) The gravity drain
backs are confused :) The oil does not know what to do :) Don't worry about it too much. It will work OK. Not worth
re-installing it plugs right :)

When you take the p-port sealing block off please take a picture of the rotor housing in that area. Is the sealing
block bolted down with four 1/4 inch bolts? Did you do the p-porting or did Jeff do it?

BTW Lewis, what email program are you using? What ever it is a lot of
work for me to save the pictures, rename them... each with a unique name and separate them from the text. I am not
complaining. I am just letting you know what is involved. It appears to be an MS Word email editor.

Paul Lamar


Lewis

What is the size of P port that can be fitted ? Are these non turbo housings? What is your asking price for the
rotor housings?

Robert


Non turbo.  P port about 1 3/4 inches, max.
Whatever its worth to you.  Shipping might be a bit costly.

Lewis.

Looks like the phasing gear is on the front(car) end housing.
Where is the rotor cooling oil squirter?

It appears to be in need of a modification of the rear(car) end housing for
rotor cooling oil drain back. If you fly it without adequate rotor cooling the apex seals may go away. The hole around the e-shaft will have to be
enlarged and another drain back hole in the main bearing housing drilled.
I'll take a look at an end housing and try to figure out the best place
for a drain back hole.

In the mean time add at least two ounces of 2 cycle oil to a gallon
of fuel to keep the apex seals cool as possible.

Richard Sohn, how are you cooling the rotor and dealing with rotor cooling oil drain back?

Paul Lamar


Picture of the shaft.  Not sure about the drain passages from the bearing.

Lewis.

The Rotary Engine News Letter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
You Tube http://tinyurl.com/beqqxas
Copyright 1998-2013 All world wide rights reserved.