Paul,
Some pictures of a tight cowling. No word yet on how well (or not) it
will cool. I'm fairly confident about the water cooling, but the oil
cooling intake, I think, is questionable. Will tie the plane down outside
and begin testing in earnest as soon as I can dig it out of the shop.
Replaced a lot of parts (almost all!) during the rebuild. Wondering if
any in the group would care for the leftovers. Chris Cosman lives
nearby... Most parts are about 1986 13b, some earlier. The rotor and
housings are nearly perfect for wear. Jeff began machining the peripheral
housing for a P port, only to learn that its through bolt spacing is
different, and will not allow for a 2 in intake. It could be made
smaller, however. I have all the 3mm seals and springs for the rotor.
Look at the pictures, make an offer and get it out of here.
Lewis Bjork
You need to replace that black rubber hose with aluminum tubing or
silicon
hose and constant tension hose clamps. I hope there is beedings on the
fittings
where the hose is clamped to. The pressure can build to 30 psi or more
in the cooling system and that 50 pound force can jerk the hose off with
disastrous over heating. I hate to see you waste all your time and money
for saving a few bucks on the cooling plumbing. Not to mentions getting
hurt or worse.
Do you have my cooling book? If not contact me by saying private and I
will get you a bargain price.
Paul Lamar
I do need to get over and see your project Lewis.
Chris Cosman
Like this?
Everything is beaded and constant tension clamps.
ran it up to 5000 rpm today. its throwing oil out the breather, I think.
too much In The tank. the o ring block around the P port has begun to
leak coolant. the o ring is in place, I think the leak is the flat side
against the housing. I used rtv sealant there. Need to fix it. any
recommendations?
also getting bogus indications from my temp and pressure senders for both
oil and water. using a MGL engine monitor. probably have to buy their
probes, too.
Lewis.
Much better. Now just make sure you don't have any air bubbles in the
rotor housing near the spark plugs up or you will melt the rotor housing.
When was the decision made to mount the engine unnaturally plugs up? :)
No telling what the oil breather is doing plugs up :) The gravity drain
backs are confused :) The oil does not know what to do :) Don't worry
about it too much. It will work OK. Not worth re-installing it plugs right
:)
When you take the p-port sealing block off please take a picture of the
rotor housing in that area. Is the sealing block bolted down with four
1/4 inch bolts? Did you do the p-porting or did Jeff do it?
BTW Lewis, what email program are you using? What ever it is a lot of
work for me to save the pictures, rename them... each with a unique name
and separate them from the text. I am not complaining. I am just letting
you know what is involved. It appears to be an MS Word email editor.
Paul Lamar
Pictures to come. Using an Ipad Mini with the apple email program. Sorry
for the trouble.
Engine was originally built by Lou Ross. He made the decision for plugs
up. Using an older ignition trigger/distributor, won't fit the plane if
turned right side up.
There is a bleed near the plugs to get air bubbles out of the coolant.
Original fwf weight was 273 lbs., much labor and money makes it 220 lbs
now, ready to go.
Jeff did the P port. Beautiful work. I'll go after the leak tomorrow.
Lewis.
Lewis,
I'd love to see more pic's, lots more pics. Are the RB end plates or how did
you lose 53 pounds,
John
The Rotary Engine News Letter. Powered by Linux.
ACRE NL web site.
http://www.rotaryeng.net
You Tube
http://tinyurl.com/beqqxas
Copyright 1998-2013 All world wide rights reserved.