Subject: turbocompounding a 20B with a DD15 power turbine-interested too
From: rotary engine
Date: 3/9/2013, 6:48 AM
To: AAA-rotaryeng


Paul,

Did you ever run the turbo compound Mazda with the gearbox shown in the
pictures?  If you did, were the results published?  Looks like a neat
project but it probably consumed lots of time and money.

Gary Knutson


Not yet. The box cost a bunch. I spent so much money on that I had none
left over for dyno time :) It is actually cheaper to use a turbo
compound system from a mass produced truck engine. Detroit Diesel DD15.
Almost bolt on with a three rotor. You would no happen to have access to
a dyno would you.

Paul Lamar

Paul,

Do you have a plan for dyno testing a turbo compound setup?  Are all the
parts and a suitable test engine available?  How about a exhaust system,
etc.

I do have access to a well instrumented and equipped test cell but my "run
time" is somewhat limited.  A test would have to be laid out and
documented and as much of the hookup stuff done ahead of time as
possible.  The facility is local (to me).

Let me know what you might have in mind.  It would be an interesting test!

Gary Knutson

I have a simple plan. Run 500 RPM increments for one minute each with
out the TC and measure and record the fuel flow and HP. Then repeat with
the TC.

I have a stock 3 rotor but it is not complete and running. It has the
stock turbo's. It needs a Motec installed. We can get help on that
because Jim Medere of Racing Beat has done it several times.

I don't currently have a Motec. He sells them I think.

We can buy the DD15 TC system new for about $4000. I can rig a cog belt
drive from the DD15 gear box out put to the 3 rotor out put shaft if I
have dwg of the dyno bell housing bolt pattern. I would entail cutting
slots in a  stock Mazda bell housing for the belt to pass through. The
belt HP would be in the range of 30 HP plus or minus 20. The DD15 GB
puts out 1800 RPM or so max when the turbine is going 40,000 RPM. That
means would would have to step it up 1 to 3 or so.

I can fly up there and spend the time hooking things up.
I think the data output from the Motec would be all we need.
We would have to monitor engine temperature of course and RPM but even
that the Motec would know.

I would probably be cheaper for me to deliver the engine than crating
and shipping. Which would run about $1000 as I just had a 400 pound
engine shipped from Or and that is what it cost.

1500 miles at 20 MPG and $4 a gallon is $300 each way.

Paul Lamar

Paul,

Am I missing something here?  I thought you were located at the Santa
Paula Airport near Ventura.  I'm in Laguna Niguel and the dyno is in
Huntington Beach.  If I'm correct on your location, things aren't all that
far apart.

This dyno, unlike a Superflow or similar, mounts the engine on adjustable
stands.  It uses a CV coupling that bolts to a flywheel or adapter plate
on the flywheel end of the output shaft.  A short drive shaft couples the
engine to the absorption unit.  No bell housing is involved.  The dyno had
a built in starter.

As the output end is exposed, it should be possible to install a driven
pulley from the TC unit.

Any required engine mounting plates and the coupling adapter should be
made ahead of time.  I can supply pictures and dimensions for the parts.

I can look around and see if I can find a "loaner" Motec.  I can't promise
anything there.

From your description, it sounds like you would run with a turbocharged
engine, is that correct?

The cost of the TC system is a pretty big hit for a test.  I suppose that
it could be reused if all went as planned.  The belt drive won't be that
bad.  I assume that the TC unit could be mounted on the engine.

Anyway, lots to think about.  I hope I cleared up some of the "travel"
concerns.

Gary Knutson


I was missing something :) That's great. I thought for some reason you
were in the Detrot area. Come on up to SZP and see my collection.
Email me before you come so I can get out to the hangar.


That $4000 includes the DD15 turbo. If we use the sequential turbos on
the 3 rotor we won't need the DD15 turbo. In theory we wont get as much
HP out of the blow down turbine due to a bit of energy loss in the
second 3 rotor turbo. I would be ecstatic with just a 5% improvement in
the BSFC. That would drop the rotary BSFC from .47 to .446 more than
demonstrating the potential.

Paul Lamar

Paul,

I may take you up on that offer.  I "escaped" from Livonia at the end of
1987. :-)


Which way would make the most sense - Mazda turbos and the DD15 without the
turbo or the other way around?  The DD15 looks like a nice package.
Would there be drawbacks to using it complete?

As I mentioned, this could be a interesting & helpful project. Who knows, it
might even be a bit of a money maker.  I will look forward to hearing more
of your thoughts on things.

Gary Knutson
--
As a 20B owner and a bit of a rotary fanatic, I too would like to see this
as a working item, along with that Lycoming cs psru ----together they would
make nice long distance cruise packages for a kit airframe meant for
travelling.....? More pics and stats if you guys really do this (and parts),
please!!!
Marc W


Maybe you could use some tax payers money Paul, at least they will get a return via something that "actually works" ha ha ha. would be a first !!
  You might be able to get a TC unit  on loan, DD might be pursuaded if
you promise to get some data for them and return the unit afterwards.
I reckon if you can give them some figures they can redesign a turbine
and turbo for minimal extra cost that would suit our purposes better,
20B 13B etc. Maybe let DD deal with govt funding if you are prepared
to work with them. Could work yes?!?! Just a thought
  BTW Motec supply the ecu 's for V8 supercars, as per the torque meter.
  Graeme Riley


-- 
The Rotary Engine News Letter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
You Tube http://tinyurl.com/beqqxas
Copyright 1998-2013 All world wide rights reserved.