Subject: Cowling and loose parts
From: rotary engine
Date: 3/10/2013, 4:40 PM
To: undisclosed-recipients:;


 Paul,
 Some pictures of a tight cowling.  No word yet on how well (or not) it
will cool.  I'm fairly confident about the
 water cooling, but the oil cooling intake, I think, is questionable. Will
tie the plane down outside and begin testing
 in earnest as soon as I can dig it out of the shop.


 Replaced a lot of parts (almost all!) during the rebuild.  Wondering if
any in the group would care for the leftovers.
 Chris Cosman lives nearby...  Most parts are about 1986 13b, some
earlier.  The rotor and housings are nearly perfect
 for wear.  Jeff began machining the peripheral housing for a P port, only
to learn that its through bolt spacing is
 different, and will not allow for a 2 in intake.  It could be made
smaller, however.  I have all the 3mm seals and
 springs for the rotor.  Look at the pictures, make an offer and get it
out of here.


 Lewis  Bjork

 You need to replace that black rubber hose with aluminum tubing or silicon
 hose and constant tension hose clamps. I hope there is beedings on the
fittings
 where the hose is clamped to. The pressure can build to 30 psi or more
 in the cooling system and that 50 pound force can jerk the hose off with
disastrous over heating. I hate to see you
 waste all your time and money for saving a few bucks on the cooling
plumbing. Not to mentions getting hurt or worse.


 Do you have my cooling book? If not contact me by saying private and I
will get you a bargain price.

 Paul Lamar

 I do need to get over and see your project Lewis.

 Chris Cosman

 Like this?


 Everything is beaded and constant tension clamps.

 ran it up to 5000 rpm today.  its throwing oil out the breather, I think.
 too much In The tank.  the o ring block
 around the P port has begun to leak coolant.  the o ring is in place, I
think the leak is the flat side against the
 housing.  I used rtv sealant there.  Need to fix it.  any recommendations?
 also getting bogus indications from my temp and pressure senders for both
oil and water.  using a MGL engine monitor.
 probably have to buy their probes, too.

 Lewis.

 Much better. Now just make sure you don't have any air bubbles in the
rotor housing near the spark plugs up or you
 will melt the rotor housing.

 When was the decision made to mount the engine unnaturally plugs up? :)
 No telling what the oil breather is doing plugs up :) The gravity drain
 backs are confused :) The oil does not know what to do :) Don't worry
about it too much. It will work OK. Not worth
 re-installing it plugs right :)

 When you take the p-port sealing block off please take a picture of the
rotor housing in that area.  Is the sealing
 block bolted down with four 1/4 inch bolts? Did you do the p-porting or
did Jeff do it?

 BTW Lewis, what email program are you using? What ever it is  a lot of
 work for me to save the pictures, rename them... each with a unique name
and separate  them from the text. I am not
 complaining. I am just letting you know what is involved. It appears to
be an MS Word email editor.

 Paul Lamar

 Pictures to come.  Using an Ipad Mini with the apple email program. Sorry
for the trouble.
 Engine was originally built by Lou Ross.  He made the decision for plugs
up.  Using an older ignition
 trigger/distributor, won't fit the plane if turned right side up.
 There is a bleed near the plugs to get air bubbles out of the coolant.
 Original fwf weight was 273 lbs., much labor and money makes it 220 lbs
now, ready to go.
 Jeff did the P port.  Beautiful work.  I'll go after the leak tomorrow.


 Lewis.

Hello Lewis,

Which MGL are you using and would you share your experience setting it up
on the rotary.  Incidentally, Matt at MGL told me I would need their
sensors for oil pressure and water temp.  I am considering their Odyssey
EFIS with RDAC and would appreciate your thoughts.

William Hagood
--

What is a an MGL?

Paul Lamar


William, have you looked at MGL's new EFIS, the iEFIS.

http://www.mglavionics.com/html/iefis.html

Uses WiFi node to connect to an iPad or any tablet, for a backup/normal or
multiscreen display), similar prices

Alex
-- 
The Rotary Engine News Letter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
You Tube http://tinyurl.com/beqqxas
Copyright 1998-2013 All world wide rights reserved.