Subject: Cowling and loose parts
From: rotary engine
Date: 3/10/2013, 4:36 PM
To: AAA-rotaryeng
CC: Jim Mederer <jimmederer@yahoo.com>


Paul,
Some pictures of a tight cowling.  No word yet on how well (or not) it will
cool.  I'm fairly confident about the
water cooling, but the oil cooling intake, I think, is questionable. Will tie
the plane down outside and begin testing
in earnest as soon as I can dig it out of the shop.


Replaced a lot of parts (almost all!) during the rebuild.  Wondering if any in
the group would care for the leftovers.
Chris Cosman lives nearby...  Most parts are about 1986 13b, some earlier.  The
rotor and housings are nearly perfect
for wear.  Jeff began machining the peripheral housing for a P port, only to
learn that its through bolt spacing is
different, and will not allow for a 2 in intake.  It could be made smaller,
however.  I have all the 3mm seals and
springs for the rotor.  Look at the pictures, make an offer and get it out of
here.


Lewis  Bjork

You need to replace that black rubber hose with aluminum tubing or silicon
hose and constant tension hose clamps. I hope there is beedings on the fittings
where the hose is clamped to. The pressure can build to 30 psi or more
in the cooling system and that 50 pound force can jerk the hose off with
disastrous over heating. I hate to see you
waste all your time and money for saving a few bucks on the cooling plumbing.
Not to mentions getting hurt or worse.


Do you have my cooling book? If not contact me by saying private and I will get
you a bargain price.

Paul Lamar

I do need to get over and see your project Lewis.

Chris Cosman

Like this?


Everything is beaded and constant tension clamps.

ran it up to 5000 rpm today.  its throwing oil out the breather, I think.  too
much In The tank.  the o ring block
around the P port has begun to leak coolant.  the o ring is in place, I think
the leak is the flat side against the
housing.  I used rtv sealant there.  Need to fix it.  any recommendations?
also getting bogus indications from my temp and pressure senders for both oil
and water.  using a MGL engine monitor.
probably have to buy their probes, too.

Lewis.

Much better. Now just make sure you don't have any air bubbles in the rotor
housing near the spark plugs up or you
will melt the rotor housing.

When was the decision made to mount the engine unnaturally plugs up? :)
No telling what the oil breather is doing plugs up :) The gravity drain
backs are confused :) The oil does not know what to do :) Don't worry about it
too much. It will work OK. Not worth
re-installing it plugs right :)

When you take the p-port sealing block off please take a picture of the rotor
housing in that area.  Is the sealing
block bolted down with four 1/4 inch bolts? Did you do the p-porting or did Jeff
do it?

BTW Lewis, what email program are you using? What ever it is  a lot of
work for me to save the pictures, rename them... each with a unique name and
separate  them from the text. I am not
complaining. I am just letting you know what is involved. It appears to be an MS
Word email editor.

Paul Lamar

Pictures to come.  Using an Ipad Mini with the apple email program. Sorry for
the trouble.
Engine was originally built by Lou Ross.  He made the decision for plugs up.
Using an older ignition
trigger/distributor, won't fit the plane if turned right side up.
There is a bleed near the plugs to get air bubbles out of the coolant.
Original fwf weight was 273 lbs., much labor and money makes it 220 lbs now,
ready to go.
Jeff did the P port.  Beautiful work.  I'll go after the leak tomorrow.


Lewis.

Hello Lewis,

Which MGL are you using and would you share your experience setting it up on the
rotary.  Incidentally, Matt at MGL told me I would need their sensors for oil
pressure and water temp.  I am considering their Odyssey EFIS with RDAC and
would appreciate your thoughts.

William Hagood
--
What is a an MGL?

Paul Lamar


Lewis, I am just getting into rotaries and have purchased a flood car engine,
13b.  I need two rotor housings and 3 mm seals. What is your price?
Ken Burdges

Ken,
These parts are pretty old.  The rotor housing is partially machined for a P port.  Unserviceable for anything else.  Internal wear conditions, rotor and end plates near perfect condition. $50 to make it official, you pay shipping.Bjorkacro

Paul,
See MGLavionics.com. Fairly capable efis units and sundry items.  South African designed, I think.



William,
So far, the temperature probes (not MGL) seem to be working.  Early difficulties stemmed from one probe sending increased temps with increasing resistance, the other probe working in reverse.  Found a new probe that reads the same way.  Still sorting out the pressure senders. Both are MGL and not working well.  Oil pressure reads zero.  I could feel heat in the lines, tank, etc. so knew the oil to be moving around, but no pressure.  Put voltage to the sending wires and could make a reading on the unit, but the senders themselves have been obnoxious to set up.
Disaster followed shortly.  The pressure regulator stuck closed for a few minutes with the engine idling.  Noticed the restricted flow and got curious.  Found metal in the oil.  Tore down the engine to find spalling in the two end bearings and some light scoring in the rotor bearing. Needless to say, bearings are out for replacement.  Thankfully, the shaft, housings and other parts look fine.

The RB aluminum end plates do not allow for two oil pressure regulators. I built up the engine using only one.  This time around, I will tap into the oil tank with a secondary regulator and improve the flow. Probably install a temporary mechanical pressure gauge for testing.


Lewis.


-- 
The Rotary Engine News Letter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
You Tube http://tinyurl.com/beqqxas
Copyright 1998-2013 All world wide rights reserved.