Subject: Cowling and loose parts
From: rotary engine
Date: 3/13/2013, 4:21 AM
To: AAA-rotaryeng


 Paul,
 Some pictures of a tight cowling.  No word yet on how well (or not) it
will
 cool.  I'm fairly confident about the
 water cooling, but the oil cooling intake, I think, is questionable.
Will tie
 the plane down outside and begin testing
 in earnest as soon as I can dig it out of the shop.


 Replaced a lot of parts (almost all!) during the rebuild.  Wondering
if any in
 the group would care for the leftovers.
 Chris Cosman lives nearby...  Most parts are about 1986 13b, some
earlier.  The
 rotor and housings are nearly perfect
 for wear.  Jeff began machining the peripheral housing for a P port,
only to
 learn that its through bolt spacing is
 different, and will not allow for a 2 in intake.  It could be made
smaller,
 however.  I have all the 3mm seals and
 springs for the rotor.  Look at the pictures, make an offer and get it
out of
 here.


 Lewis  Bjork

 You need to replace that black rubber hose with aluminum tubing or silicon
 hose and constant tension hose clamps. I hope there is beedings on the
fittings
 where the hose is clamped to. The pressure can build to 30 psi or more
 in the cooling system and that 50 pound force can jerk the hose off with
 disastrous over heating. I hate to see you
 waste all your time and money for saving a few bucks on the cooling
plumbing.
 Not to mentions getting hurt or worse.


 Do you have my cooling book? If not contact me by saying private and I
will get
 you a bargain price.

 Paul Lamar

 I do need to get over and see your project Lewis.

 Chris Cosman

 Like this?


 Everything is beaded and constant tension clamps.

 ran it up to 5000 rpm today.  its throwing oil out the breather, I
think.  too
 much In The tank.  the o ring block
 around the P port has begun to leak coolant.  the o ring is in place,
I think
 the leak is the flat side against the
 housing.  I used rtv sealant there.  Need to fix it.  any recommendations?
 also getting bogus indications from my temp and pressure senders for
both oil
 and water.  using a MGL engine monitor.
 probably have to buy their probes, too.

 Lewis.

 Much better. Now just make sure you don't have any air bubbles in the
rotor
 housing near the spark plugs up or you
 will melt the rotor housing.

 When was the decision made to mount the engine unnaturally plugs up? :)
 No telling what the oil breather is doing plugs up :) The gravity drain
 backs are confused :) The oil does not know what to do :) Don't worry
about it
 too much. It will work OK. Not worth
 re-installing it plugs right :)

 When you take the p-port sealing block off please take a picture of
the rotor
 housing in that area.  Is the sealing
 block bolted down with four 1/4 inch bolts? Did you do the p-porting
or did Jeff
 do it?

 BTW Lewis, what email program are you using? What ever it is  a lot of
 work for me to save the pictures, rename them... each with a unique
name and
 separate  them from the text. I am not
 complaining. I am just letting you know what is involved. It appears
to be an MS
 Word email editor.

 Paul Lamar

 Pictures to come.  Using an Ipad Mini with the apple email program.
Sorry for
 the trouble.
 Engine was originally built by Lou Ross.  He made the decision for
plugs up.
 Using an older ignition
 trigger/distributor, won't fit the plane if turned right side up.
 There is a bleed near the plugs to get air bubbles out of the coolant.
 Original fwf weight was 273 lbs., much labor and money makes it 220
lbs now,
 ready to go.
 Jeff did the P port.  Beautiful work.  I'll go after the leak tomorrow.


 Lewis.

 Hello Lewis,

 Which MGL are you using and would you share your experience setting it
up on the
 rotary.  Incidentally, Matt at MGL told me I would need their sensors
for oil
 pressure and water temp.  I am considering their Odyssey EFIS with
RDAC and
 would appreciate your thoughts.

 William Hagood
 --
 What is a an MGL?

 Paul Lamar


 Lewis, I am just getting into rotaries and have purchased a flood car
engine,
 13b.  I need two rotor housings and 3 mm seals. What is your price?
 Ken Burdges

Ken,
These parts are pretty old.  The rotor housing is partially machined for
a P port.  Unserviceable for anything else.  Internal wear conditions,
rotor and end plates near perfect condition. $50 to make it official,
you pay shipping.Bjorkacro

Paul,
See MGLavionics.com. Fairly capable efis units and sundry items.  South
African designed, I think.



William,
So far, the temperature probes (not MGL) seem to be working.  Early
difficulties stemmed from one probe sending increased temps with
increasing resistance, the other probe working in reverse.  Found a new
probe that reads the same way.  Still sorting out the pressure senders.
 Both are MGL and not working well.  Oil pressure reads zero.  I could
feel heat in the lines, tank, etc. so knew the oil to be moving around,
but no pressure.  Put voltage to the sending wires and could make a
reading on the unit, but the senders themselves have been obnoxious to
set up.
Disaster followed shortly.  The pressure regulator stuck closed for a
few minutes with the engine idling.  Noticed the restricted flow and got
curious.  Found metal in the oil.  Tore down the engine to find spalling
in the two end bearings and some light scoring in the rotor bearing.
Needless to say, bearings are out for replacement.  Thankfully, the
shaft, housings and other parts look fine.

The RB aluminum end plates do not allow for two oil pressure regulators.
 I built up the engine using only one.  This time around, I will tap
into the oil tank with a secondary regulator and improve the flow.
Probably install a temporary mechanical pressure gauge for testing.


Lewis.

Hello Lewis,

Thanks for sharing and good luck on the rebuild.

William Hagood


-- 
The Rotary Engine News Letter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
You Tube http://tinyurl.com/beqqxas
Copyright 1998-2013 All world wide rights reserved.