Subject: Cowling and loose parts
From: rotary engine
Date: 3/15/2013, 6:25 AM
To: AAA-rotaryeng


 Paul,
  Some pictures of a tight cowling.  No word yet on how well (or not) it
 will cool.  I'm fairly confident about the
  water cooling, but the oil cooling intake, I think, is questionable. Will
 tie the plane down outside and begin testing
  in earnest as soon as I can dig it out of the shop.


  Replaced a lot of parts (almost all!) during the rebuild.  Wondering if
 any in the group would care for the leftovers.
  Chris Cosman lives nearby...  Most parts are about 1986 13b, some
 earlier.  The rotor and housings are nearly perfect
  for wear.  Jeff began machining the peripheral housing for a P port, only
 to learn that its through bolt spacing is
  different, and will not allow for a 2 in intake.  It could be made
 smaller, however.  I have all the 3mm seals and
  springs for the rotor.  Look at the pictures, make an offer and get it
 out of here.


  Lewis  Bjork

  You need to replace that black rubber hose with aluminum tubing or silicon
  hose and constant tension hose clamps. I hope there is beedings on the
 fittings
  where the hose is clamped to. The pressure can build to 30 psi or more
  in the cooling system and that 50 pound force can jerk the hose off with
 disastrous over heating. I hate to see you
  waste all your time and money for saving a few bucks on the cooling
 plumbing. Not to mentions getting hurt or worse.


  Do you have my cooling book? If not contact me by saying private and I
 will get you a bargain price.

  Paul Lamar

  I do need to get over and see your project Lewis.

  Chris Cosman

  Like this?


  Everything is beaded and constant tension clamps.

  ran it up to 5000 rpm today.  its throwing oil out the breather, I think.
  too much In The tank.  the o ring block
  around the P port has begun to leak coolant.  the o ring is in place, I
 think the leak is the flat side against the
  housing.  I used rtv sealant there.  Need to fix it.  any
recommendations?
  also getting bogus indications from my temp and pressure senders for both
 oil and water.  using a MGL engine monitor.
  probably have to buy their probes, too.

  Lewis.

  Much better. Now just make sure you don't have any air bubbles in the
 rotor housing near the spark plugs up or you
  will melt the rotor housing.

  When was the decision made to mount the engine unnaturally plugs up? :)
  No telling what the oil breather is doing plugs up :) The gravity drain
  backs are confused :) The oil does not know what to do :) Don't worry
 about it too much. It will work OK. Not worth
  re-installing it plugs right :)

  When you take the p-port sealing block off please take a picture of the
 rotor housing in that area.  Is the sealing
  block bolted down with four 1/4 inch bolts? Did you do the p-porting or
 did Jeff do it?

  BTW Lewis, what email program are you using? What ever it is  a lot of
  work for me to save the pictures, rename them... each with a unique name
 and separate  them from the text. I am not
  complaining. I am just letting you know what is involved. It appears to
 be an MS Word email editor.

  Paul Lamar

  Pictures to come.  Using an Ipad Mini with the apple email program. Sorry
 for the trouble.
  Engine was originally built by Lou Ross.  He made the decision for plugs
 up.  Using an older ignition
  trigger/distributor, won't fit the plane if turned right side up.
  There is a bleed near the plugs to get air bubbles out of the coolant.
  Original fwf weight was 273 lbs., much labor and money makes it 220 lbs
 now, ready to go.
  Jeff did the P port.  Beautiful work.  I'll go after the leak tomorrow.


  Lewis.

 Hello Lewis,

 Which MGL are you using and would you share your experience setting it up
 on the rotary.  Incidentally, Matt at MGL told me I would need their
 sensors for oil pressure and water temp.  I am considering their Odyssey
 EFIS with RDAC and would appreciate your thoughts.

 William Hagood
 --

 What is a an MGL?

 Paul Lamar


William, have you looked at MGL's new EFIS, the iEFIS.

http://www.mglavionics.com/html/iefis.html

Uses WiFi node to connect to an iPad or any tablet, for a backup/normal or
multiscreen display), similar prices

Alex
-- 

Hello Alex,

Yes I have been eyeing (or is that i-ing) the new EFIS. Still pondering.

William Hagood

Please sign your email messages. It is extra work for me.

Paul Lamar

-- 
The Rotary Engine News Letter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
You Tube http://tinyurl.com/beqqxas
Copyright 1998-2013 All world wide rights reserved.