Subject: early slide throttle pictures
From: rotary engine
Date: 3/18/2013, 3:01 AM
To: AAA-rotaryeng




 This engine won many 24 hour races before the rotary was
 heavily handicapped.


 Paul Lamar


 I would buy injector blocks like those, seats unmachined so
 the end user could finish then to suit their own injectors.
 Anyone else interested? Jeff?
 C. Smith

 Mechanical injection ?

 Paul Lamar

 I'm talking about the design of the piece that holds the injectors,
 the seats radialy centered on the intake tube not talking about
 using mechanical injection.
 C. Smith

 What is the matter with this design? It was done this way to simplify
 the fuel rail. You need a minimum of two injectors per p-port runner to
 get fine control over the amount of fuel injected over the power and RPM
 range. The RX8 engine uses three per rotor.

 Some of the fuel may impinges on the side wall but it evaporates
 eventually and is not lost. The vapor eventually goes in the engine.

 Matter can neither be created nor destroyed. It is a law of physics.
 It is just not a good idea. IT IS THE LAW! :)



http://en.wikipedia.org/wiki/**Conservation_of_energy<http://en.wikipedia.org/wiki/Conservation_of_energy

 To "crack" gasoline into other constituent molecules takes a lot of
 heat. The intake  manifold usually runs ice cold due to evaporation.

 Paul Lamar


 I didn't say anything was the matter with your design. I like the other
 one better. No fuel rail at all, how simple is that?. Since I'm not
 using the narrow injectors you designed it for, I was going to use
 components from Kinsler, and plumb it similar to the early slide
 throttle image you posted. Saves having to weld up a fuel rail,
 individual injectors can be removed without disturbing the rest of them,
 etc.
 C. Smith

 How do you attach the fuel hose to the standard injectors?

 Can you get a screen shot from the Kinsler catalog?

 Paul


 Is this what you have in mind?

 Notice there is no groove for the retention clip on the RX8 or Siemans
 skinny injectors.

 Most people now use the skinny injectors. The fat GM injectors are more or
 less obsolete.

 We have spent a lot of thought on this subject over the past 15 years :)

 I would love to have a injector that you could just screw on a hose
 fitting. It would allow much more flexibility in where exactly injectors
 were mounted.

 It might be possible to cut a grove in the plastic RX8 injectors but one
 would risk a failure with the hose coming off and the high pressure fuel
 squirting everywhere.

 Paul Lamar



 Here's one way from SDS EFI.

Mark St

Remarkable similar to what I had in mind:)

Paul Lamar
-

BTW Mark, do you have any experience with their EFI for a rotary?
How is it programed?

Paul Lamar

No, I've only used their injector bungs on one of my many intakes.  I am running RWS efi.

Mark S

You are up early. What time is it there :)

How much of an improvement did you notice when you moved one of
the injectors closer to the rotor housing? Was that the only thing
you did at the time?


BTW I am beginning to like the Model T ignition idea using the data
selector :)

We could have a code sw on the instrument panel 0 degrees BTDC for start. 22 degrees BTDC for high power and 30 degrees BTDC for high altitude lean cruise. Klaus runs 30 degrees  BTDC at altitude and 50 or 100 degrees F lean of peak and gets 100 MPG.

The electronics could be on the PC board with the hall effect sensors.

Paul Lamar

-- 
The Rotary Engine News Letter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
You Tube http://tinyurl.com/beqqxas
Copyright 1998-2013 All world wide rights reserved.