Subject: early slide throttle pictures
From: rotary engine
Date: 3/18/2013, 10:40 AM
To: AAA-rotaryeng


This engine won many 24 hour races before the rotary was
heavily handicapped.


Paul Lamar


I would buy injector blocks like those, seats unmachined so
the end user could finish then to suit their own injectors.
Anyone else interested? Jeff?
C. Smith

Mechanical injection ?

Paul Lamar

I'm talking about the design of the piece that holds the injectors,
the seats radialy centered on the intake tube not talking about
using mechanical injection.
C. Smith

What is the matter with this design? It was done this way to simplify
the fuel rail. You need a minimum of two injectors per p-port runner to
get fine control over the amount of fuel injected over the power and RPM
range. The RX8 engine uses three per rotor.

Some of the fuel may impinges on the side wall but it evaporates
eventually and is not lost. The vapor eventually goes in the engine.

Matter can neither be created nor destroyed. It is a law of physics.
It is just not a good idea. IT IS THE LAW! :)




http://en.wikipedia.org/wiki/**Conservation_of_energy<http://en.wikipedia.org/wiki/Conservation_of_energy

To "crack" gasoline into other constituent molecules takes a lot of
heat. The intake  manifold usually runs ice cold due to evaporation.

Paul Lamar


I didn't say anything was the matter with your design. I like the other
one better. No fuel rail at all, how simple is that?. Since I'm not
using the narrow injectors you designed it for, I was going to use
components from Kinsler, and plumb it similar to the early slide
throttle image you posted. Saves having to weld up a fuel rail,
individual injectors can be removed without disturbing the rest of them,
etc.
C. Smith

How do you attach the fuel hose to the standard injectors?

Can you get a screen shot from the Kinsler catalog?

Paul


Is this what you have in mind?

Notice there is no groove for the retention clip on the RX8 or Siemans
skinny injectors.

Most people now use the skinny injectors. The fat GM injectors are
 more or
less obsolete.

We have spent a lot of thought on this subject over the past 15 years :)

I would love to have a injector that you could just screw on a hose
fitting. It would allow much more flexibility in where exactly injectors
were mounted.

It might be possible to cut a grove in the plastic RX8 injectors but one
would risk a failure with the hose coming off and the high pressure fuel
squirting everywhere.

Paul Lamar



Here's one way from SDS EFI.

   Mark St

   Remarkable similar to what I had in mind:)

   Paul Lamar
   -

   BTW Mark, do you have any experience with their EFI for a rotary?
   How is it programed?

   Paul Lamar

   No, I've only used their injector bungs on one of my many intakes.  I
 am running RWS efi.

 Mark S

 You are up early. What time is it there :)

 How much of an improvement did you notice when you moved one of
 the injectors closer to the rotor housing? Was that the only thing
 you did at the time?


 BTW I am beginning to like the Model T ignition idea using the data
 selector :)

 We could have a code sw on the instrument panel 0 degrees BTDC for
 start. 22 degrees BTDC for high power and 30 degrees BTDC for high
 altitude lean cruise. Klaus runs 30 degrees  BTDC at altitude and 50 or
 100 degrees F lean of peak and gets 100 MPG.

 The electronics could be on the PC board with the hall effect sensors.

 Paul Lamar


Paul,

The dog woke me up at 4:20 a.m.  I wasn't sleeping anyway, so I got
up, fed the dog, made coffee and checked email.  I go to bed early to
make up for it though.

The reason I moved the primary injectors was due to fuel puddling
against the throttle plages at idle.  Moving the primaries downstream
of the throttle plates appears to have corrected the problem.  The
secondary injectors are still located about a foot from the ports.

Mark S.

Maybe a 1/16th hole in the throttle plate or a tiny notch in the runner
wall would have solved that  problem. It is amazing it sealed that well.
--
Paul Lamar



_Paul, I have been a casual reader of your blog for over a year and am very impressed with your engineering knowledge and attention to detail as exemplified by your comments on the injector blocks.  I now have a strong interest in building an aircraft rated rotary engine(Hopefully with turbo compounding)  and wonder if you have considered writing a manual on how to build such an engine and where to find the components?

I  also wonder about the supply of parts if no one is manufacturing automobile rotary engines today.

I know you have a manual on “How to Cool a Rotary”.  How to make a rotary could be sold for much more and would be a great service to the homebuilder community.

Regards,

Bobby Summerville

I have thought about another book but it is a question of time.
Right now the big push is getting the cost down on motor mounts.
They can cost half the price of an engine and cost several hundred dollars to ship.

There is nothing special about building a rotary engine for aircraft.
A stock engine works fine. One can download shop manuals here.

http://foxed.ca/index.php?page=rx7manual

Read this for intake systems.

http://www.rotaryeng.net/fund-of-intake.html

If you ask specific questions everybody will benefit and the information will be up to date as we are learning new things all of the time.

Paul Lamar

-- 
The Rotary Engine News Letter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
You Tube http://tinyurl.com/beqqxas
Copyright 1998-2013 All world wide rights reserved.