Subject: Robo welder is rotating VERY FIRST WELD
From: rotaryeng
Date: 3/26/2013, 5:07 PM
To: AAA-rotaryeng








Robo welder is rotating. Not welding yet but soon.
It amazes me that tiny motor and gear box is all you need.

Here is a movie to prove it.

Just because something you are building is small does not mean it does not take a lot of time.

I tried the rubber tubing coupler but it did no rotate smoothly.
It would wind up and then would release.
This is a special coupling nut with a 4-40 set screw.

Paul Lamar


I am getting a degree in robo welder design.

I have discovered several things. Don't use caster wheels that are the least bit soft. It is best to make your own rollers out of metal.

The grounding of the tube resting on the stop doesn't work very well.
I found some 4 gage wire in  an automobile hi fi audio shop that is very flexible. A zillion tiny copper wires.
I stripped the insulation off but not entirely necessary.
The insulation is soft and flexible as well.
About 2 bucks a foot.


I will attach that to the tube with
a hose clamp and wrap several turns around the tube to be unwrapped as the tube turns and is welded.

I found a 110 Volt synchronous motor at MaMaster Carr that rotates at exactly 1 RPM no matter what. It has enough torque to twist your wrist off.

It takes the speed of welding out of the equation. All you need set is the welding current and the distance of the tungsten to the metal.
The gas flow can be near the bottom of the recommended scale to conserver that expensive consumable.

Paul Lamar


A bit of advice from someone who has thousands of hours experience with welding wire in a physically dynamic environment. First, properly size the wire for the current load. #2 for 100A give or take depending on the insulation(bumping 1 or 2 languages here won't kill you). You always want to size on the high side because.. it's expensive to replace. Welding wire has many fine conductors, composed of alloys that resist fatigue and heat crystallizing. Welding wire, is quite properly more expensive because it handles abuse and motion.
If your robo welder only needs 360/380 degrees of rotation, get enough length so you can perform the rotation without too much twist per inch of wire, but always turn it back to a start index.
C. Smith



tig does not use wire. Filler rod sometimes but not needed here.
This is basically an over lapped joint.
Here is a picture of the part that is welded on to the end of the
4130 .049" wall one inch OD tube. The turned down part goes inside the end of the tube.

Paul Lamar

I believe C.Smith is talking about the ground wire. Being an electrical engineer, he is right, #2 copper is the right size for 100 amps.

H.Lunt

Thanks.

BTW everybody please set your editors to send plain text to me.

html does strange things to email programs.

We are getting email from different OS's XP, Wind 7, Wind 8 etc., etc.. Mac, cell phones etc., etc., etc. Apparently they send messages in different ways. Some in html.

Paul Lamar

I'll go buy another 3 feet of the 4 gage and double up on it.

Paul Lamar


This was a wild ass guess on current (80 amps), gas flow (12.5 CFH) and tungsten distance (about 1/8 inch).

The 60 Cycle synchronous gear motor was rotating at 1 RPM. You can set your watch on it.

I am going to have a party tonight :)

This is as close to a perfect weld as it gets.

The last picture was some welding done by the best welder I know. He is a guy that works for George Talbot Talins company in Torrance Ca.

Paul Lamar



Paul, I've been around TIG welding for quite a while. My friend runs the
shop for an aircraft parts company that supplies STC parts for Super Cubs.
The weld you have created looks every bit as good as the ones done by the
certified welders working in his shop. One of the catch phrases used by his
welders is "Looks like a machine did it"...Very good work, yours really look
nice.

Rick in Alaska

Thanks Rick. This is part of significantly cutting the cost of a rotary
installation. Motor mounts are now under $500 and can be shipped anywhere
at relatives low cost.

BTW what OS and email program are you using?

Paul Lamar

The Rotary Engine News Letter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
You Tube http://tinyurl.com/beqqxas
Copyright 1998-2013 All world wide rights reserved.