Some of this boils down to the practical application. Yarns ago dump
trucks and farther back all trucks had gasoline engines. All heavy
trucks are powered by diesels due to engine life and economy dictated
the change. We use 3/4 or 1 ton trucks as required by the contracts
with the oil companies. Gasoline trucks must be no more than 3 years
old with diesels allowed 5 years. Most of the time we have electrical
or instrumentation tools and materials in the trucks, so lightly
loaded. The new emsisions diesels are not getting much better economy
than the gasoline trucks with all else equal. Add in the fact that
oil and filter changes are 2 to 3 times the cost. Now if you are
pulling a trailer on a regular basis as you are, a diesel is the only
way to go. It comes down to application and the correct equipment for
the job. Light duty is not likely the place for diesel engines used
in urban settings. Diesel engines converted to run on natural gas in
urban delivery and city buses where fuel can be readily available and
close will come into popularity in time due to the clean burn. Fuel
economy on NG is better than on converted gas engines due to the
compression ratio. NG can be used with 15:1 to 16:1 CR. As Paul
stated, all diesels will be equipped eventually.
Dale Davies
Hi folks. I just joined this list, hoping to get some good
information about running rotary engines in aircraft. So far, I've
seen little of that, but I'm still hopeful.
Rotary engines - A long time ago I had a friend, Dan Duncan, who
built aircraft rotary engine conversions, and I came to believe that
they were great airplane engines. In the late 1980's, I designed a
pusher airplane that used a Mazda 13b as the core for an internal
combustion high-bypass fan, dumping heat into the bypass and
expanding the airflow. I never got far enough with the design to
build it. These days I'd like to put a rotary in my airplane and
maybe some day build that other airplane if I get around to it.
Carbon - Carbon is what I like to call the "crack whore" element of
the periodic table (see
http://en.wikipedia.org/wiki/Periodic_table). It will happily form a
covalent or ionic bond with just about anything, which is why you
don't want it in your body in its raw form - it likes to muck with
your DNA. Mutated DNA leads to mutated cells, some of which grow
uncontrollably and lead to death by cancer.
Diesel Ash - Breathing ash is bad for you. All research shows that
breathing ash is bad for you. Your lungs don't work if you put ash in
them, and if the carbon from the ash makes its way into the rest of
your body, the rest of your body won't work either.
Nature doesn't care what you believe about it.
Cheers, all. Dave Klingler
Did Duncan disappear to Mexico ? Do you know where he is?
Some up set people are still looking for him :)
Paul Lamar
For those who don't know who we're talking about, Dan Duncan was the
owner of Duncan Aviation, purveyors of rotary aircraft engines (not
to be confused with the Duncan Aviation that now crops up in Google).
They made a line of aircraft engines based on some Israeli drone
engines on the bottom end up through a turbocharged Mazda 12A. They
did some NASA SBIRs on rotary engines for aircraft, including some
longevity studies. They were comprised of Dan Duncan, his wife and a
few employees, in Oklahoma.
I'm going to recount what I recall as well as I can remember it.
Apologies if I make any mistakes.
In 1986, Dan heard about a tech company incentive program in New
Mexico. He and his wife inquired to find out whether their company
qualified. It did, so they shut down operations in Oklahoma and moved
to Santa Fe. Unfortunately, by the time they finished the move, a
new governor had taken office, one who had different ideas about
incentive programs. He shut down the program immediately. The tax
breaks and cheap loans dried up just as Dan and his wife finished
moving, and they found themselves in a tight spot. Dan's wife wrote
all the customers and told them there would be a delay in delivering
their engines, and then the two of them set to building engines as
fast as they could. Dan's wife got a side job at JC Penney to earn
money for parts.
I had a friend back then who was a retired master machinist from the
nuclear weapons program, and I was helping him to build an
amphibious bushplane. He looked over Dan's little operation, met Dan
and his wife, liked what he saw, and purchased an engine.
At that point Dan had delivered around 70 engines and had a two-year
backlog of orders, including the one my friend purchased. One of the
customers was a doctor in Oklahoma who had ordered an engine just
before they moved. When he got the letter from Dan's wife, he wrote
back, demanding that Dan deliver his engine immediately. Dan wrote
him a reply, telling him that he was going as fast as he could but
offering him a refund on his deposit. The doctor did not reply but
went to one of his friends, who happened to be U.S. Attorney Bill
Price of Oklahoma. Price was readying a campaign for governor the
following year, 1989, and in some of his pre-campaign appearances he
began mentioning Dan, his brother and "ridding Oklahoma of the
Duncans of this world". Dan, unfortunately, didn't know about that.
The feds busted down Dan's door at about 6 one morning, charged him
with one count of mail fraud for each letter they found in his filing
cabinet, close to 400 counts, and extradited him back to Oklahoma.
He had hoped to be gone for a few days, long enough for the hearing
and bail, but he sat in New Mexico for a few weeks before the
extradition took place. When he got to Oklahoma, the guards beat him
up and his hernia started bleeding internally. That landed him in the
prison hospital, and he ended up being gone for several months.
Toward the end of that time one of his wife's coworkers convinced her
to file for divorce.
When he finally got out on bail, he lived on baked potatoes in his
hangar, drove a truck for a local moving company, and delivered my
friend's engine. He gave me his dog to care for, and went back to
trial in Oklahoma. He was able to prove that he had delivered engines
for all but three of the letters the Feds had confiscated, the two
letters to the doctor and the reply. They found him guilty of three
counts of mail fraud, not what he had hoped for.
They then kept him in prison for what I remember was around 19
months. He returned to Santa Fe, rented an apartment from my dad, and
took odd commercial hauling jobs. I watched him struggle pretty hard
to pay off debts and build engines for people when he was able. He
lived on a sack of baked potatoes and a block of cheese for many
months before and after he lost his business, and most of his
earnings went into trying to hold on to his Piper Pacer and buy
engine parts. His health and morale declined considerably during the
time I knew him. He missed his ex-wife terribly, and he spent
considerable attention on trying to win her back.
The last time I saw Dan he was leaving town to drive for a Canadian
trucking company. I think he had followed his ex-wife back to Canada.
I think he delivered 79 engines in all, including one for the plane
I was helping to build; the doctor would have been his 80th, had he
been able. I never saw him again, and I've always wondered what
happened to him. I think by now he'd be about 70.
I know a very little bit of what he did to make his engines last. One
thing was that he had discovered that the stock Mazda water pump
cavitates at high RPMs, so he substituted a Ford Escort water pump
and that took care of it. He also dynamically balanced all of his
engines. The engines he tested for NASA hit his target of 3000 hours
under load at 9000 RPMs, not too shabby.
Paul, if you know of some information about Dan Duncan I'd like very
much to hear what you know.
Dave
Its been so long I forgot all the bad things. I do recall he made too
many modifications to the engine.
Now a days we use the engine as is more or less. Except for P-ports.
BTW that is a myth on the water pump cavitation. We don't run the
engine over 7500. It might cavatate at 11,000 RPM.
Paul Lamar
Hi Paul & All,
Re: Dan Duncan 12a single rotors,
I bought the 12a per photo's on Ebay 2007.
It is a front rotor with e-shaft direct into Psru.
It was without ignition or flywheel/starter. Ignition now is Ford
Edis4
It has a Ford water pump cartridge p/n 771-8505-AA casting,
crosses to 79/80 Fiesta p/n GMB 125-1010
The Psru has 59 tooth ring, 31 tooth sun & 14 tooth planet for
2.91 to 1.
I need Help to identify the gear set, very robust, for
consideration on my 20b project.
The gear set may be from a B/W 72c Velvet drive marine reduction,
has same ratio?
I did 1st. start on the 13b single rotor project this past week,
Youtube/JgW-D_4UOc & N1S1yQhKQ_0
Best Regards,
Rolland Savoie
Flock Kitfoxes
12a & 13b single rotors running
20b project
The Rotary Engine News Letter. Powered by Linux. ACRE NL web site.
http://www.rotaryeng.net You Tube
http://tinyurl.com/beqqxas
Copyright 1998-2013 All world wide rights reserved.