Subject: Porting Air Cooled Wankels SAE Paper list
From: rotaryeng
Date: 5/16/2013, 8:23 PM
To: AAA-rotaryeng




Anybody know where I can find info on the best way to port them? It
seems that some are ported in such a way that the air flows through
the spinning rotor(s), "cooling" them and is recycled in a way as to
warm the intake air for better fuel burn...? Is PP the best way to go
always? It almost seems to me that it may be best to keep the stock
porting (maybe smooth everything out) AND PP them while also
blocking/rerouting the heated air from "recycling" for better hp.
Thoughts? Links to air cooled wankel porting? Thanks! Dan G.

It depends on how the rotor is cooled and what kind of rotor bearings
are used. If there is an oil cooling system and the rotor bearings
are the plain bearing type, p-porting is best for maximum power.
Unfortunately there are no such Wankel engines in production.

Paul Lamar


  Hi!: the subject seems not being much addressed today, but there are
some SAE papers specific on air cooled Wankel RCEs:

Small Wankel Engines -Helmut Keller, Fichtel and Sachs, SAE paper 680572
The Rotary Engines of Yanmar Outboard Motor -Kojiro Yamaoka and Hiroshi
Tado,
    SAE paper 710581
Outboard Marine Corp.s Production Rotary Combustion Snowmobile Engine
   Harry M. Ward et al, SAE paper 730119
Improvements of the Rotary Engine with a Charge Cooled Rotor
   -K Yamaoka and H Tado, SAE paper 720466
Analysis of Light-Load Performance in Rotary Engines, Toshiyuki Kohno et
al,
   from Toyota, SAE paper 790435
A Review of Curtiss-Wright Rotary Engine Developments with Respect to
General Aviation Potential, Charles Jones, SAE paper 790621
Syvaros SP-440, Air Cooled, Rotary-Trochoidal Engine, Andrei Adam,
  SAE paper 800974
Dvelopment of the Norton Rotary Motorcycle Engine, D. W. Garside,
  SAE paper 821068
A Comprehensive Study of Wankel Engine Performance R. Sierens et al,
  SAE paper 830332
The Effect of Alcohol Blends on the Performance of an Air Cooled Rotary
Trochoidal Engine, Marcel Gutman and Izu Luster, SAE paper 840237
The Introduction of a New Ultra-Lite Multipurpose Wankel Engine,
Dankwart Eiermann et al, SAE paper 900035
Rotary Engine Powered Ducted Fan for Aircraft Applications, Mike Griffith
and Paul Moller, SAE paper 900037
On the Wankel Engine with high Pressure Recirculation of Unburned Gases
Marcos Langeani, SAE paper 921444 (Close to the Yamaha and Kawasaki
patents?)
A Two-Dimensional Computer Simulation of Exhaust Gas Behavior Inside a
Rotary
Engine System, Yuji Hamai and Eisuke Outa, SAE paper 930681
The Characteristics of Fuel Consumption and Exhaust Emissions of the
Side Exhaust
  Port Rotary Engine Ritsuharu Shimizu et al, Mazda, SAE paper 950454
Wankel Engine for Hybrid Powertrain Angelo Butti and Vincenzo Delle Site,
SAE paper 951769
Developed Technologies of the New Rotary Engine (RENESIS) Masaki Ohbuko
et al,
Mazda, SAE paper 2004-01-1790
Numerical Analysis of Combustion and Flow Inside a Small Rotary Engine
for Developing
an Unmanned Helicopter, Takafumi Yamada, Yasuo Moriyoshi, SAE paper
2007-32-0098

Papers marked  are not solely devoted to air cooling, or even are not
about this.

The general issues of Peripheral Porting vs Side Porting are addressed
in the two editions
of the book Rotary Engine, by Kenichi Yamamoto, Mazda, 1969 and 1981,
both contain
very different subjects, and even when its copyrighted material, it can
be found and
downloaded from the web.

As you know, SAE papers can be bought and downloaded from www.sae.org ,
usual prices
are around $24 per paper, and if you become a member a reduction in
prices applies,
probably theres much more info than this, but my envy in spending money
just for
curiosity is limited, however, some spend much more with drug dealers,
tobacco and
alcohol, and the diseases that come after.

If this is of help to you, and you arrive to build or modify a working
engine, please let us know.

Regards, salut +

    Jose Gros-Aymerich
    Madrid, Spain



Running hot air into the intake will not increase horse power no matter
where you got the heat from.  That is why an intercooler is used on
turbocharged engines.  A cooler denser air fuel charge will always
produce more power than a hotter thinner air fuel charge.  Not that it
matters much with a rotary, but a cooler charge also has less tendency
to preignition.

Air cooling of the rotor has been tried before.  Air has a much lower
specific heat than oil so it takes a whole lot more air to cool the
rotor.  Pumping all that air sucks up a whole bunch of horse power.
Also, because the air is so much less efficient at cooling the output of
the engine must be constrained to avoid overheating.

The rotor bearings must be lubricated.  Blowing the required large
quantities of air through the rotor carries away large amounts of the
oil used to lubricate the bearings.  The result of that is either loss
of large amounts of oil, or carrying a large heavy oil separator along.
While I will agree that the weight of the blower and separator are
most likely less than the weight of the liquid cooling system, I'm quite
certain that the additional horse power made possible by the increased
efficiency of the liquid cooling system will far outperform the lighter
air cooled system in climb performance.

There's no point in P porting an air cooled Wankle because it already
produces as much horse power as the cooling system can absorb.  The only
purpose for P porting a rotary is to increase the horse power of the
engine by increasing the volumetric efficiency of the engine.  More
horse power is produced by burning more air/fuel in the same time span
resulting in more heat that needs to be dissipated into the cooling
system.  The cooling system is the limiting factor in an air cooled engine.


-  Mark LaPierre


The Rotary Engine News Letter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
You Tube http://tinyurl.com/beqqxas
Copyright 1998-2013 All world wide rights reserved.