I know there have been rotary diesels made that were
self-supercharging, but I was wondering if the same could be done with
a 13B style engine. I was thinking along these lines:
The front rotor would have a custom housing with a mirrored p-port
setup such that it created an intake and compression event on both
sides of the housing. This compressed air would be ducted together
and then to the intake of the rear rotor giving you an nearly 2:1 PR
supercharge (there would be some losses). When compressed at ~9:1 in
the rear, the total CR would be around 18:1, which would be sufficient
for compression ignition. The leading plug could be replaced by a
direct injection nozzle, and the trailing plug could be a glow plug.
There would be some things to work out with sealing, housing
thickness, etc, to handle compression ignition, but I think it's
doable.
A quick guesstimation showed that this should produce around 100-120hp
at 7500 rpm counting the power needed for the compressor section.
Combined with a turbo, you could probably push it to 150-175...
turbocompound would be even better.
Any thoughts?
Josh
Diesel exhaust is hazardous to your health according to WHO ....AKA
World Health Organization.
A diesel rotary may not run at 7500 RPM because of burn rate issues.
Paul Lamar
Hi!: Rolls-Royce, I don't remember well if it was RR or Mercedes who
discovered the nickasil coverage for trochoid surface,
worked in a two-stage Diesel Rotary Combustion Wankel Engine for
military purposes, it had a big lower section rotor that acted as
a compressor, and an smaller upper high pressure section rotor where
combustion took place, the author was David W Garside,
and a report about it exists in a technical publication of the British
Society of Automobile Engineers proceedings.
The inherent problem in compression ignition Wankel RCEs would be that
the nature of Wankel engine makes impossible because of
geometrical reasons obtaining in a single rotor compression ratios high
enough for the Diesel range, there is at least a SAE paper
about a low compression ratio Diesel Wankel RCE, but the images of the
chimney they used to evacuate exhaust gases show a very
thick smoke column.
There are some patents on other two-stage arrangements for Wankel RCE
Diesel engines where the big and the small rotors are placed in line,
not one over the other as in the Garside design, but I'm not aware of
any practical unit using the concept, you can access the
patents by entering ESPACENET, and then, in advanced search mode,
writing the key words -Diesel or -Compression Ignition -Rotary Engine
Should you have news, please let us know.
Regards, salut +
Jose Gros-Aymerich
I bought that paper regarding the RR 2 stage diesel. It's definitely
interesting, and there is some useful information, but most of it is
quite dated. Holy smokes though... $32 for that paper... info that
old should be free to anyone bored enough to read it.
I think that with some research into the design of the rotor dish and
compression ignition, good seals (maybe double side seals along with
ceramic apex seals), and a supercharger, this concept is definitely
workable. I think when replacing anything smaller than the O-320, the
self-supercharging idea would probably be ok. For O-320 and larger,
you'd probably want to go ahead and add a supercharger like the 1.6L
whipple to get the pressure up high enough and use both rotors for
power.
A turbo could act as a normalizer, a power adder, or it could take
over for the supercharger all together once at altitude and play both
rolls. The latter sounds like it would be the most efficient option,
but you'd have to have a bigger turbo than with the first option.
That's about all I have for now.
Josh
The Rotary Engine News Letter. Powered by Linux.
ACRE NL web site.
http://www.rotaryeng.net
You Tube
http://tinyurl.com/beqqxas
Copyright 1998-2013 All world wide rights reserved.