Subject: 650 HP P-port turbo 2 rotor in Harmon Rocket Latest Picts
From: rotaryeng
Date: 6/12/2013, 10:13 AM
To: undisclosed-recipients:;



 This is a time to climb to 10,000 meters record attempt. Time to
 climb is all about power to weight ratio and the Wankel rotary
 engine excels in that category.


 Allan Tolle in a 300 HP Power Sport 2 rotor running on NOS and 100LL
 in an RV3 holds the unofficial dead stop to 3000 feet record at just
 under a minute.

 Jim Mederer of Racing Beat fame is building the all aluminum (200
 pounds bare) 2 rotor p-port turbo charged 650 HP engine.

 Jim is a bit anal about rotor housing cooling hence the sprint
car V8
 water pump :) To my knowledge Jim never installed a "cylinder head"
 temperature gage so this is based on a guess of what the rotor
 housing temperature might be. The drag racers get many runs out of
 such an engine.

 This is also a tribute to the robust Mazda Wankel engine. In street
 form the most HP Mazda every sold was 280 HP. 650 HP or more is
 normal for drag racing. This engine will not use NOS but it would be
 good for at least an additional 100 HP.

 If one pumped up an aircraft piston engine to this level one would
 have a exploded hand grenade in 15 seconds :)

 The engine is being installed in an all ready flying Harmon (REAL!)
 Rocket. The gear box is a Bell 47 helicopter final drive. First used
 with a rotary back in 1973 by Dave Garber in his huff and puff Reno
 racer. (Never got it to cool as that was long before my book on "How
 to Cool Your Wankel").

 Taking off in a high power to weight ratio prop plane is challenging
 to say the least. One must feed the power in slowly but not too
 slowly to get the record.

 Russ McFarland, an expat American, living in New Castle Australia,
 is sponsoring this project.

 Now if I could only get him to sponsor a turbo compound rotary
 ....:)

 Paul


 Latest pictures.

 They figure it is going to climb out at a 80 degree angle at 110
 MPH.

 Cooling by liquid spray on heat exchangers. Either water or alcohol.
 I suspect alcohol or acetone would work better as Jim wants to keep
 the coolant temperature down to an extraordinary 190 F.

 Any total loss spray fluid must evaporate to extract a large amount
 of heat.

 BTW the turbo is equipped with a tach to keep the turbo turbine
 blades from flying off.


 Paul Lamar




 OOOOhhhhh.......Only an Aussie will do this....(or a tame
American)....

 BTW Paul, can you recommend a book or any other home-built
how-to stuff that gives a idea of how to build a high hp 2-port?
P-port, of course, turbo, what else?

 Erik in Oz.

http://www.rotaryeng.net/fund-of-intake.html
http://www.rotaryeng.net/Welded-steel-p-port.html
http://www.rotaryeng.net/slide-throttle.html
http://www.youtube.com/watch?v=NKJ00JsnS8A

Now over 90,000 hits.


A good book on turbo chargers is Turbochargers by Hugh MacKinnis

Integrate the plenum on the end of both intake tubes with the inter cooler as in these pictures.


Paul Lamar
-- 
The Rotary Engine News Letter. Powered by Linux. ACRE NL web
site. http://www.rotaryeng.net You Tube
http://tinyurl.com/beqqxas Copyright 1998-2013 All world wide
rights reserved.