Paul, (I am not an engineer...nor do I claim anything mechanical
skills.... question for you and the group)
Molt Taylor's Flying Car.... utilized a ??? Centrifugal clutch on the
drive shaft .... with ball bearings (?) About five of them are still
in existence and flying today.........
Why would not a modern version of that clutch work on the Rotary
engine?
Paul,
Been reading in depth about the rotary VERY interesting engine for an
aircraft. The turbo compounding takes this to the next level.
Barron
That is my next project. Chris's bell housing put the project over
the top. It eases adapting the DD15 TC system to a 3 rotor.
I was planning on using the Mazdatrix dyno but that would not mate
with Chris's bell housing so I need to build another prop dyno. I
will use one of these ideas.
Paul Lamar
How is the PSRU development going, you could test the new unit with
the turbo-compound and kill two birds with one stone.
Graeme Riley
Paul,
What HP is your psru designed for? Can it handle 350+ hp for takeoff
and 300 hp continuous?
Mark S.
You mean the one Milo is working on? It is based on a recycled six
cylinder lycoming crank shaft. It uses stock Ford six pinion
planetaries.
It has mostly to do with the weight of the prop.
With carbon blades it would be no problem.
Paul Lamar
Paul,
My experience has been that the weak link isn't necessarily the
planets, but something else, like the rivets holding the flex plate
adapter to the hub, or the weld/pin attaching the sun gear to the
input shaft, etc. I was curious as to the design spec for this box. I
know you're trying to keep it light, but there's a limit to where you
are willing to go.
Mark S.
Has anybody pulled down one of Tracy's psru's that has some time on
it. I'm aware of Dave's sun gear issues I was wondering how the rest
of the unit was holding up. Dave did you install a second pin in the
sun gear, If so have you inspected it since? Just curious as to the
results. Graeme Riley
It is showing some weakness in the higher 3 rotor HP levels. The flex
plate is cracking.
IMHO it is due to the lack of an effective torsional damper. In
effect capturing the rubber bushing in an enclosed metal box like
Tracy has done is no damper at all.
They don't work as one might think. If you totally enclose a rubber
bushing (as Tracy has done) it no it longer operates as rubber. It
acts as a solid. Rubber is no more compressible than hydraulic
fluid.
I am building this combo flex plate and damper for the 3 rotor turbo
compound engine I am working on. .090 4130 would be fine for a 2
rotor. For a 3 rotor p-port or turbo I would use .125" thick 4130
Motor cycle style rubber bushings can be made with red RTV in a
Teflon mold. Good to 500 F.
Paul Lamar
I have been reading about a psru developed for the R1200 bmw
motorcycle engine that is used in aircraft tractor and trike pusher
configuration. It uses a centrifugal clutch like ones in most
chainsaws only much larger, this has solved the torsional dampening
problem. The engines are rated 100-115hp continuous 6300 rpm. The
clutch eengauges at 1800 - 2000 rpm and has to be changed every 400
hrs. These engines have run 2000 hrs in this configuration. They
initially had flywheel cracks when they used light ones, beefed them
up cracks stopped engine ran smoother.
Has anyone considered the rubber coupling used to couple a high hp.
electric motor to air compressors and pumps ect. If i understand
there operation correctly they will absorb energy transmitted back to
the motor and shaft miss alignment between motor and equipment. I
have seen these couplings with several thousand hrs. on them with no
visible wear. Steve Hudson
How high is the HP?
Paul Lamar
Hi. The clutch does not solve the problem as much as avoid it. The
clutch does not engage until the engine is above the resonant speed
of the system. There is sometime a rubber coupling also to bring the
critical point to lower rpm.
http://www.elbe-group.de/presse/download/Folder_Gelenkscheiben_e_low.pdf
Rubber coupling designed for industrial and automotive use, by BMW,
Mercedes. and others. Porsche used one between flywheel and gearbox
on their aircraft engine which was known for its smooth running if
nothing else. Three point engine mounting helped. Also used by some
auto and motorcycle geared PSRUs.
Murry I. Rozansky
I would but when you scale it up for 200 or 300 HP it gets much
larger and heaver.
In the future when one is trying to be helpful think of the space
and weight of what one is suggesting. Get a dwg. of the device and
see if it will fit in a 6 inch dia. cyl. and 1.7 inches long. The
devil is always in the details.
Paul Lamar
Paul,
I'm unfamiliar with the units referenced in the above URL for the rubber
BMW style couplers, so I can't tell if they would handle 7,500 rpm or not,
but I suspect not.
Mark S.
-- The Rotary Engine News Letter. Powered by Linux. ACRE NL web site.
http://www.rotaryeng.net. You Tube
http://tinyurl.com/beqqxas.
Copyright 1998-2013 All world wide rights reserved.