I counted the teeth of the gear reduction in the DD15 gear box. The
turbine gear had 22 teeth and the big gear had 107 teeth. That is a
gear reduction of 4.86:1.
That means at 40,000 turbine RPM (the reputed operating RPM of the
DD15 power recovery turbine) the out rotates at 8,230 RPM.
PERFECT FOR THE ROTARY!!!!!!!!!!!
Looking into the huge exhaust port of the turbine the turbine is
rotating clockwise. Looking at the output shaft of the TC gear box it
is rotating counter clockwise.
Looking at the rotary from the bell housing end the rotary e-shaft
also rotates counter counter clockwise. The exhaust and intake on the
right.
IT COULD NOT BE BETTER IF THE DD15 TURBO COMPOUND SYSTEM HAD BEEN
DESIGNED FOR THE ROTARY!!!!!!!!!
All we now need is a simple shaft coupling. shown in the 3D as a
black cylinder. No cog belt drive lash up necessary.
This would make a great boat engine. A turbo charged P-port 3 rotor
followed with a DD15 turbo compound system.
1000 HP at a BSFC in the diesel range. Below .4 !!!!!!! 20,000 hour
life with all ceramic seals.
1000 to 1500 pounds less weight than a diesel with about the same
fuel burn.
Paul Lamar
Fantastic news and great job !
Anyhow, I'm a bit puzzled about 2 points :
1/ DD15 turbine and reduction gear box is supposed to run at steady
speed if fed with "tranqulized" exhaust gas flow. but, in the same
time the torque and thus the rotation speed of the engine is
pulsating. A belt drive could provide a certain amount of damping,
and if slipping, some torque clipping. With a direct coupling is
there no need for a dedicated damping device, or is it built in the
DD15 gearbox itself ?
2/ The DD15 turbine is designed to work downstream of the diesel
turbocharger. In a way, it looks very much like a Low pressure
turbine stage located downstream of the High pressure turbine stage
of a turbofan jet engine. The design characteristics (pressure and
temperature) of the exhaust gasses feeding the DD15 should be rather
low. On the "TC-test-config31" I can't see any turbocharger between
the rotayr exhaust and the DD15 turbine. Knowing that there is a
large amout of energy to recover in a rotary exhaust gasses, is thre
no risk of "burning" the DD15 turbine ?
Of course, this problem should not occur with a turbocharged rotary.
As there is a lot of energy to recover from the exhaust gasses of a
rotary, cannot the temperature ever exceed the max design temperature
of the turbocharger ? On the Ford "ecoboost" 3 cylinder engine (100
HP with only 1 liter displacement !) this problem is solved by die
casting the exhaust pipes into the liquid cooled cylinderhead. For
automotive application, where the average power is low and liquid
cooling system is expected to heat the passengers as soon as
possible, this makes sense. For an aircraft application, where each
extra heat that flows through the liquid cooling system costs extra
weight and drag, this would be pure nonsense ! A much better solution
would be to "desuperheat" the exhaust gasses by mixing some cooler
air from the turborcharger compressor as indicated on the following
sketch.
In this case there is no extra cooling requirement nor heat losses
(lower temperature to turbocharger, but more mass flow)
(See attached file: Turbocompound rotary with desuperheater.jpg)
Philippe Dejean
1/ There is a fluid coupling inside the DD15 TC gear box.
2/ ON the stock 3 rotor sequential turbo charged engine there are two
turbo chargers. You can see them in these pictures. I did not draw
them in the 3D.
There is a risk of burning the DD15 turbine but we have a longer pipe
between the turbo and the TC so that should cool the exhaust gases.
Maybe too much so we may have to insulate part of it.
You could also carry water to inject into the exhaust during take
off. Since it would convert to steam that would be a tremendous HP
boost.
Paul Lamar
If you were to use water injection, seems like you'd want everything
downstream to be stainless.
Any chance of getting lots of detailed pictures of that turbine system?
Maybe some day in the distant future someone might want to make a scaled
version for a single-rotor. With a little digging around on Google I
haven't yet managed to find a small one being commercially made. It
seems like the DD15 is the only one being made?
Dave Klingler
Perhaps.
I am not taking it apart to take pictures. It was hard enough get the
pressed on output gear off :)
There are other units for trucks. So far the DD15 is best.
Paul Lamar
The Rotary Engine News Letter. Powered by Linux.
ACRE NL web site.
http://www.rotaryeng.net
You Tube
http://tinyurl.com/beqqxas
Copyright 1998-2013 All world wide rights reserved.